Philips FW798W - Manual (Page 29)

29
English
CLOCK TIMER
Timer Setting
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will start to
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than two seconds to select timer mode.
™ “AM 12:00” or the last set timer
starts flashing. The TIMER flag
flashes.
™ The last selected source is lit while
other available sources are flashing.
2 Press CD, TUNER or TAPE to select
the desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press␣ à or á to set the hour for the
timer to start.
4 Press␣ í or ë to set the minute for
the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The
TIMER flag remains on the display.
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the last
selected disc. If the CD trays are empty,
the TUNER will be selected instead.
– If the source selected is TAPE, and if the
preset time is reached during high
speed dubbing, the TUNER will be
selected instead.
SHUFFLE PROGRAM
FM
STEREO BACK HSD REPEAT REC LW MW AM T.A. NEWS
SOUND NAVIGATION
INCREDIBLE
SURROUND
DIGITAL
SOUND CONTROL
DYNAMIC BASS
BOOST
TAPE CD
PROG
NEWS!
RDS
DOLBY B
NR
DUB (HSD)
REC
SIDE A•B A. REV
TUNER AUX
PRESET ▲ ▲
STOP • CLEAR SEARCH • TUNING PLAY PAUSE PREV NEXT
MINI HIFI SYSTEM
C D 1 • 2 • 3 CDR TAPE 1 • 2
TIMER FRONT
60Hz 500Hz 250Hz 1KHz 2KHz 4KHz 8KHz
VOLUME
S S
L R
C
PRO LOGIC
CLOCK/
TIMER
STANDBY
ON
View Clock
You can view the clock (if it is set) while
the system is in standby mode or any
source mode. It will be displayed for about
seven seconds.
• Press CLOCK/TIMER briefly (on the
system only).
™ “PM 10:38” (the current time)
will be displayed.
™ “--:--” will be displayed if the
clock is not set.
Clock Setting
The clock is set in 12-hour mode, e.g. “ AM
12:00“ or “PM 12:00“. Before
setting the clock, you must be in the View
Clock mode.
1 Press CLOCK/TIMER to select clock
mode.
™ “AM 12:00” or the current time
starts flashing.
2 Set the hour with␣ à or á.
3 Set the minute with␣ í or ë.
4 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.