Pioneer BDP-LX52 User Manual

Page 56

picture is displayed or the

picture is not displayed
properly.

Is the video cable

properly

connected?

• Connect the cable

properly according to the connected devices

(

page 13).

• Inse

rt the cable firmly and all the way in.

Is the video cable damaged?

If the cable is damaged,

replace it with a new one.

Is the in

put setting on the

connected TV o

r AV receiver

r amplifier right?

Read the o

perating instructions of the connected components and

switch to the

proper input.

re you viewing the picture

rom the video output

rminal selected with

VIDEO

SELECT?

ress

VIDEO SELECT to switch the video output terminal to be viewed

(

page 21).

Is the out

put video resolution

properly set?

Use

OUTPUT RESOLUTION to switch to a resolution at which the video

and audio signals a

re output (page 21).

• Is the

player connected

with an HDMI cable othe

than a High S

peed HDMI™

cable (with a Standa

HDMI™ cable)?

• A

re you using an HDMI

cable with built-in equalize

1080

p or Deep Color video signals may not be output properly,

pending on the HDMI cable being used or the player’s settings.

ress

 while pressing  on the player’s front panel to restore the

video out

puts to the factory default settings. After this, if you wish to

out

put the video signals with 1080p or Deep Color, connect the TV

using a High S

peed HDMI™ cable without built-in equalizer, then reset

the

player using the

Setup Navigator (page 18).

Does the connected TV
su

pport the frame rate of the

video signal being out

put by

the

player?

If the

picture is not displayed when playing a disc with a frame rate that

is not su

pported, the picture will not be displayed even when playback

is sto

pped. In this case, use the procedure below to switch the frame

rate of the video signals output from the player.
Eject the disc and close the disc t

ray. Then, press

 OPEN/CLOSE

while

pressing

 on the player’s front panel to switch to a frame rate

pported by the connected TV.

NTSC on PAL TV properly

set?

When viewing the video signals out

put from the player’s S-Video or

Video te

rminal, set

NTSC on PAL TV properly (page 37).

Is a DVI device connected?

The

picture may not be displayed properly if a DVI device is connected.

HDMI Color Space

properly set?

Change the

HDMI Color Space setting (page 38).

Pictu

re freezes and the front

panel and remote control
buttons sto

p working.

• P

ress

 STOP to stop playback, then restart playback.

• If the

playback cannot be stopped, press

 STANDBY/ON on the

player’s front panel to turn off the power, then turn the power back on.

• If the

power cannot be turned off, press and hold

 STANDBY/ON

on the

player’s front panel for over 5 seconds. The power will turn off.

Motion is unnatu

ral or

picture is not clear.

Change the

Pure Cinema setting (page 34).

picture is displayed or

picture is not output in high
definition when

playing BDs.

With some discs, it may not be

possible to output the video signals from

the

VIDEO output terminal or the COMPONENT VIDEO output

rminals. In this case, connect using an HDMI cable (page 13).

• Pictu

re is disturbed during

playback.

• Pictu

re is dark.

• This

player supports Macrovision analog copy protection technology.

With some TVs (such as with built-in video deck), the

picture will not be

dis

played properly when the copy protected DVD title is played. This is

not a malfunction.

• If the

player and TV are connected via a DVD recorder/video deck,

etc., the

picture will not be displayed properly due to analog copy

protection. Connect the player and TV directly.

Problem

Check

Remedy

LX52_VXJ5_IBD_EN.book 56 ページ２００９年３月３日　火曜日　午後７時２９分