Philips ShowView MX5100VR/02 - Manual (Page 9)

5 Select programme number '1' on the TV.
6 Confirm with B on the System remote control.The System
compares the TV channels on the TV and the System.
If the System finds the same TV channel as on the TV, then it
stores it at 'P01'.
7 Wait until the next number, e.g. 'P:02' appears in the display.
8 Select the next programme number on the TV, e.g. '2'.
9 Confirm with B.
10 Repeat steps 7 to 9 until you have assigned a programme num-
ber to all TV channels.
11 To end, press DISPLAY/STATUS/EXIT.
I cannot switch my TV set to programme number '1'
* If you have connected additional devices to socket
AV2(DECODER), please disconnect these devices. Because of
other connected devices, the TV set could switch to the pro-
gramme number of the scart socket.
'NO TV SIGNAL' will appear in the TV screen.The
System is not receiving a video signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see which scart socket
is used for video signals.
If this does not help, it's not possible to use this function. Please
read the section 'Sorting and Clearing TV channels manually'.
Follow TV (Automatic TV channels sorting)
When the automatic channel search function is activated, the
TV channels are saved in a specific order.This may vary from
the order of TV channels on the TV.
This function changes the order of TV channels saved in the
System to match that of the TV.
Make sure that the System and the TV are connected by a
scart cable.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select TUNER SET
UP, then press B.
3 Press K/L to select 'FOLLOW TV'
, then press B.
4 'P:01' will appear in the System dis-
play.
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
END=EXIT
9
English
Setting Up your System
Automatic Channel Setup
You can programme the tuner to scan only the channels that
you can receive in your area.
1 Turn on the TV and select the video out channel on your TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select TUNER SET UP, then press B.
4 Press K/L to select AUTO TUN-
ING, then press B.
• The System distinguishes SECAM
or PAL automatically.
• The tuner scans and memorizes
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorized
channel.
5 Press SKIP/P+ G / SKIP/P- H or numerical key pads to scan
through channels you have received.
Manual Channel Preset
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select TUNER SET UP, then press B.
3 Press K/L to select MANUAL
TUNING, then press B.
4 Press K/L to select SYSTEM, then
press B to appear your desired
system.
5 Press K/L to select PROG., then
press B.
6 Press K/L or numerical key pads
to select your desired programme number, then press B.
• You can select programme number 01-99.
7 Press K/L to select CHANNEL, then press B.
8 Press K/L.The System tuner will begin to search up or down
automatically.When a channel is found, the System will stop
searching and the picture will appear on the TV Screen.
• You can select desired channel number by using numerical
key pads.You must refer to the channel plan and press three
digits to select the channel number. (To select channel 24,
first press “0” button then press “2” and “4”).
• If this is the channel you want, press B.
• If you want to remove scrambled signals, press K/L to select
DECODER.Then, press B to select [ON].
9 Press DISPLAY/STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the
SKIP/P+ G G / SKIP/P- H H buttons.
– You should select the satellite channels to be received by
the satellite receiver directly on the receiver itself.
MANUAL TUNING
SYSTEM [ L ]
→PROG. P55
CHANNEL 055
DECODER [OFF]
SKIP [OFF]
SET=K L OR 0 – 9
END=EXIT
PLEASE WAIT
START FINISH
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
E9017FD_EN.qx3 03.8.6 10:13 AM Page 9