Panasonic WV-CW474S - Manual (Page 4)

1. CAMERA SETUP MENU
This camera utilizes an on-screen user setup menu.
• Opening the Setup Menu
Press and hold down
I(S) for 2 seconds
or more.
The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.
Refer to the following sections for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END in the bot-
tom line, and press
I(S) to close the setup menu.
Note: If no button is pressed for 6 minutes while a setup menu is being displayed on the
monitor screen, it is automatically closed and the mode returns to the normal camera
picture.
2. SETUP OPERATION
This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM
SET UP menu, use the following buttons on the side panel.
Left Button (
I
) (L) : Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each
time this button is pressed.
Right Button (
I
) (R) : Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each
time this button is pressed.
Up Button (
I
) (U) : Moves the cursor upwards. Use this button to select an item or
adjust the parameters.
Down Button (
I
) (D) : Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Set Button (
I
) (S) : Executes selections and displays a submenu for an item with the
mark.
• To reset the parameter to the factory default setting, move the cursor to the parameter
to be reset and press
I(L) and I(R) simultaneously.
• To return to the previous menu or page, move the cursor to RET and press
I(S).
• To close the setup menu, move the cursor to END and press
I(S).
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both
I(L) and I(R), press I(S) for a few seconds. The message
ALL RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you can-
not change the currently active settings. This is to prevent accidental changing of the
settings.
To edit the CAM SET UP menu (change
settings), press
I(U) and I(D) or
I(L) and I(R) to move the cursor to
SET UP DISABLE in the bottom line.
Press
I(S). SETUP DISABLE changes
to SETUP ENABLE. Move the cursor to
DIP SW. Press
I(S). DIP SW changes
to MENU. Then move the cursor to the
item(s) you want to change.
Notes:
• When DIP SW is selected for CAM SET UP menu, five modes can be set with the DIP
switches.
• To operate the camera functions with the system controller, select MENU in the CAM
SET UP menu.
Important Notice:
When the setup menu is closed after changing the parameters in the menu, the new
values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only
Memory). These values remain valid until new values are stored, even if the power of
the camera is off.
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
DIP SW
END SET UP DISABLE
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
MENU
END SET UP ENABLE
↵
↵
↵
SETUP
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
DIP SW
END SET UP DISABLE