Powerware 9315 User Manual

Powerware Hardware

Table of contents

Document Outline

Powerware 9315 UPS 500–750 kVA Installation and Operation Manual
Chapter 1 - Introduction
- 1.1 UPS Features
- 1.2 Options and Accessories
- 1.3 Basic System Configurations
- 1.4 Safety Warnings
- 1.5 Conventions Used in This Manual
- 1.6 For More Information
- 1.7 Getting Help
Section I - Installation
Chapter 2 - UPS Installation Plan and Unpacking
- 2.1 Creating an Installation Plan
- 2.2 Inspecting and Unpacking Each Cabinet
Chapter 3 - Installing the UPS System
- 3.1 Preliminary Installation Information
- 3.2 Unloading the UPS Cabinets from the Pallet
- 3.3 Single Module Installation
  - 3.3.1 Installing UPS Internal Power and Control Wiring
  - 3.3.2 Installing UPS External Power and Control Wiring
- 3.4 Multi‐Module Installation
  - 3.4.1 Installing UPS Internal Power and Control Wiring
  - 3.4.2 Installing UPS External Power and Control Wiring
- 3.5 Installing Input/Rectifier Customer Connections
- 3.6 Installing Output/Inverter Customer Connections
- 3.7 Installing Accessories
- 3.8 Initial Startup
- 3.9 Completing the Installation Checklist
- Installation Checklist
Chapter 4 - Installing a Remote Battery Disconnect
Chapter 5 - Installing a Remote Emergency Power-off Control
- 5.1 REPO Installation
- 5.2 REPO Operation
Chapter 6 - Installing Optional Accessories
- 6.1 Installing an RMP
- 6.2 Installing an RIM
- 6.3 Installing an SCM
- 6.4 Installing X-Slot Cards
Section II - Operation
Chapter 7 - Understanding UPS Operation
- 7.1 Operating Modes
Chapter 8 - Using the Control Panel
- 8.1 Using the LCD Screen
- 8.2 Using the Pushbuttons
- 8.3 Adjusting the Contrast
- 8.4 Reading the Status Indicators
- 8.5 Using the Menu Options
Chapter 9 - UPS Operating Instructions
- 9.1 UPS Controls and Indicators
- 9.2 Starting the UPS
- 9.3 Starting the UPS in Bypass Mode
- 9.4 Transferring to Bypass Mode
- 9.5 Transferring to Normal Mode
- 9.6 Transferring to Bypass and Shutting Down the UPS
- 9.7 Shutting Down the UPS and Critical Load
- 9.8 Using the UPS Emergency UPM Off Pushbutton
  - 9.8.1 Using the UPS Emergency UPM Off Pushbutton
  - 9.8.2 Resetting the UPS System after an Emergency UPM Off
Chapter 10 - Using Features and Options
- 10.1 Building Alarm Monitoring
- 10.2 General Purpose Relay Contacts
- 10.3 Optional Remote Monitor Panel
- 10.4 Optional Relay Interface Module
- 10.5 Optional Supervisory Contact Module
Chapter 11 - Responding to System Events
- 11.1 System Event Horns
- 11.2 System Event Indicators
- 11.3 System Event Messages
Chapter 12 - Communication
- 12.1 Locating the Customer Interface Panel
- 12.2 Connecting Equipment to a Serial Port
- 12.3 Configuring the Serial Ports
- 12.4 Terminal Mode
- 12.5 System Configuration Mode
- 12.6 Calibration Mode
- 12.7 Computer Mode
- 12.8 Remote Monitor Mode
- 12.9 eNotify Service
  - 12.9.1 eNotify Service Features
  - 12.9.2 Installing eNotify Service
- 12.10 Remote Notification
- 12.11 X-Slot Cards
Chapter 13 - Maintaining the UPS System
- 13.1 Important Safety Instructions
- 13.2 Performing Preventive Maintenance
- 13.3 Recycling the Used Battery or UPS
- 13.4 Maintenance Training
Chapter 14 - Product Specifications
- 14.1 Model Numbers
- 14.2 UPS System Input
- 14.3 UPS System Output
- 14.4 Environmental Specifications
Chapter 15 - Warranty
Appendix A - Installation Reference
- A.1 Physical Features and Requirements
- A.2 UPS System Oneline Configurations
- A.3 Power Wiring Installation Notes
- A.4 Location of UPS Terminals
- A.5 Customer Interface Wiring Notes
- A.6 Typical REPO
- A.7 RMP Dimensions and Mounting Details
- A.8 RIM Dimensions and Mounting Details
- A.9 SCM Dimensions and Mounting Details
- A.10 Battery Disconnect Switch Dimensions
Manual Part Number and Revision