Philips DVP3200V/37B - Manual (Page 29)

English
Timer Recording (cont’d) 29
● If you are recording from other equipment, select L 1 or L2. To
determine L 1 or L2, refer to the Helpful Hints on page 28.
● If you are using a Cable Box/Satellite Receiver, select the
Cable Box/Satellite Receiver output channel (03 or 04).
Then, at the Cable Box/Satellite Receiver, select the channel
you want to record. Leave the Cable Box/Satellite Receiver
on for the timer recording.
Details are on page 10.
9 Press K or L to select a recording tape speed. The arrow
will appear beside your choice. The selected speed will flash
beside REC SPEED. Details about tape speed are on page 67.
You must select the recording speed to complete the timer programming.
• To stop a started timer
recording, press STOP/EJECT
C A
on the front of the
DVD/VCR. (You cannot stop a
started timer recording with
STOP C on the remote.) More
Helpful Hints are on page 69.
• To change incorrect
information, press s or B to
choose the item you want to
change. Press K or L to adjust
the information.
• If there is no tape in the VCR
when you press TIMER SET,
“
” will flash. Insert a tape.
• If one or more Timer
recordings are on standby when
one timer recording ends, the
DVD/VCR will turn off
automatically and “
” will
appear on the DVD/VCR’s
display panel indicating that it is
now ready for another timer
recording.
Helpful Hints
PROGRAM NUMBER 1
DATE
0 5 / 0 3 WED
START TIME 0 7 : 3 0 P M
END TIME 0 8 : 3 0 P M
CHANNEL 16
REC SPEED S P
B SP
SLP
ONE TIME PROGRAM
10 Press CLEAR to remove the menu.
11 Press TIMER SET. In some cases, the DVD/VCR will switch to
DVD mode instead. You may use the DVD player during a timer
recording.
If you want to use the VCR until time for the recording, don’t press
TIMER SET until a few minutes before the recording should start.
Or, press TIMER SET only when you know you won’t be using the
VCR anymore (until after the recording).When “
” is lit (not
flashing), you cannot put the DVD/VCR in VCR mode by pressing
VCR or SOURCE. You must first press TIMER SET on the remote
control or STOP/EJECT C A on the front panel to cancel the timer
recording temporarily. Then, you can use the VCR features again.
When a timer recording ends
The DVD/VCR will turn off and “ ” on the DVD/VCR’s display panel
will flash indicating that the recording is complete, then goes into the
timer standby mode again. (It may switch to DVD mode automatically.) At
this point, you cannot use the VCR unless you release the DVD/VCR
from the timer standby mode.
To release the DVD/VCR from timer standby mode
● If the DVD component is active and no more timer recordings are on
standby, you can cancel the timer standby mode by pressing TIMER SET or
VCR on the remote control or by pressing SOURCE or STOP/EJECT C A
on the front panel.
● If the DVD component is not active, or the “ ” is not flashing but lit
indicating there are more timer recordings on standby, you can cancel the
timer standby mode only by pressing TIMER SET on the remote control or
by pressing STOP/EJECT C A on the front panel.
●
After releasing the DVD/VCR from timer standby mode, you can use it as usual.
Cancelling a Timer Recording before the Recording Starts
1 Press VCR, then press DISC/VCR MENU so MENU 1 appears.
2 Press K or L to select TIMER PROGRAMMING,
then press B.
3 Press K or L to find the program you want to cancel.
4 While the program number is flashing, press s to
clear all the information for that program.
5 Press CLEAR to remove the menu.
TV/VIDEO VCR DVD VCR Plus+
SUBTITLE AUDIO ANGLE ZOOM
DVD
SETUP MENU
DISC/VCR
DISPLAY
TIMER SET
BACK
PLAY
REW FFW
PREV NEXT PAUSE
REC STOP
OK
REPEAT
REPEAT
A-B
CH
+
-
CLEAR
REC MODE SEARCH MODE TITLE
9
11
10
E8A21UD_EN1 5/29/06 3:13 PM Page 29