Panasonic AJ-HD1800P - Manual (Page 127)

127
Error messages
(continued)
_Displaying the hour-meter information
Turn the ADJ dial to move the cursor ( ¢), and the description
for the item where the cursor is located is shown as a
superimposed display.
If “T&S&M” has been selected as the setup menu item
No.006 (DISPLAY SEL) setting, a message appears in the
mode display area whenever a warning or error has
occurred. When a multiple number of errors have occurred,
the one with the highest priority is displayed.
The resettable table hour-meter information items will be
reset by your dealer when maintenance or other work is
performed.
_Display of UMID information
In the EE mode, the indication is displayed when UMID
information is available in the input signal. When a tape is
played back, the indication is displayed if the UMID
information is available on the tape. If there is no UMID
information, [NO-INFO] is displayed.
No./Item Description
H00
OPERATION
Displays in 1-hour increments the time during
which power has been supplied.
H01
DRUM RUN
Displays in 1-hour increments the amount of time
during which the drum has rotated.
H02
TAPE RUN
Displays in 1-hour increments the amount of time
during which the tape has been running in the FF,
REW, PLAY, SEARCH (JOG, SLOW and SHTL),
REC and EDIT modes (but not in the JOG, SLOW,
SHTL or STILL mode).
H03
THREADING
Displays in 1-time increments the number of times
the tape has been threaded (loaded) and
unthreaded (unloaded).
H04
F LOADING
Displays in 1-time increments the number of front
loading operations.
H05
LCD ON
Displays in 1-hour increments the amount of time
during which the LCD monitor has lighted.
H11
DRUM RUNr
Displays in 1-hour increments the amount of time
during which the drum has rotated.
(Can be reset.)
H12
TAPE RUNr
Displays in 1-hour increments the amount of time
during which the tape has been running in the FF,
REW, PLAY, SEARCH (JOG, SLOW and SHTL),
REC and EDIT modes (but not in the JOG, SLOW,
SHTL or STILL mode). (Can be reset.)
H13
THREADINGr
Displays in 1-time increments the number of times
the tape has been threaded (loaded) and
unthreaded (unloaded). (Can be reset.)
H14
F LOADINGr
Displays in 1-time increments the number of front
loading operations.
(Can be reset.)
H15
LCD ON r
Displays in 1-hour increments the amount of time
during which the LCD monitor has lighted. (Can be
reset.)
H30
POWER ON
Displays the number of times the power has been
turned on.
Priority Display and description
Higher
Lower
Error messages (see error message table):
When any problem arises with the VTR’s
operation, the AUTO OFF lamp lights, and an
error message is displayed.
INT SG:
If, when “INT SG” has been selected as the audio
input setting by (VID IN) on the
menu or by the or
menu, and the EDIT button is pressed, this
message is displayed for the first two seconds
when editing is started. In the same way, it is
displayed for the first two seconds when recording
is started.
NO INPUT:
If, when input signals (but not analog audio
signals) are not supplied to the input connector
selected by (VID IN) on the menu
or by the or menu,
the EDIT button is pressed, this message is
displayed for the first two seconds when editing is
started. In the same way, it is displayed for the
first two seconds when recording is started.
Warning messages
(see warning message table):
When a warning occurs in this VTR, the warning
lamp lights, and a warning message is displayed.
When a multiple number of warnings have
occurred, the one with the highest priority is
displayed.
Indication Contents
MATNO Material number
COPY Instance number (number of times for copying)
OWNR Country name, Organization name, User name
POS Elevation, Latitude, Longitude, Reception level from
the GPS satellite at the time of recording
HOLD: It is impossible to receive signals from the
GPS satellite.
2D: The number of satellites is a few. The
accuracy of elevation information is
insufficient.
3D: Signals from the GPS satellite are good
(strong).
DATE Date
TIME UTC (Coordinated Universal Time)
F1
F1