Panasonic AJ-SD955BP - Manual (Page 27)

27
ON
OFF
POWER
DV
DVCPRO DVCPRO 50
METER
L
R
FULL/FINE
MONITOR SELECT
HEADPHONES
MONITOR MIX A VOL SELECT INPUT SELECT PREVIEW/PREVIEW AUTO EDIT PREROLL
VIDEO
REC LEVEL
CH1
PB LEVEL
AUDIO
CH2 CH3 CH4 TC PRESET MENU SET DIAG SUPER REC INH INT TCG MODE CONTROL
ON
OFF
UNITY
VAR
COUNTER
RESET
A IN TRIM
SET
OUT IN
A OUT
CH1 CH4 CH2
INSERT
CH3
ASSEM VIDEO CUE TC STAND BY
EDIT
REW STOP
PLAY REC
PLAYER RECORDER
FF
JOG SHTL SLOW
TAPE
EE
ON REGEN
PRESET
EXIT OFF
REMOTE
LOCAL
8
9 5
4
4
4
After selecting VTR used as the player by pressing
PLAYER button, set the initial speed by the search
dial while pressing SET button.
5
Simultaneously pressing both SET button and
PREVIEW/REVIEW button results in automatic
prerolling for the both VTRs (player and recorder),
then the player VTR is operated at the set initial
speed up to the IN point.
6
After passing the IN point, turn the search dial to
memorize the playback speed of the VTR used as
the player.
7
When the tape has passed the OUT point set by
recorder, the memory of the playback speed will
terminate.
8
When AUTO EDIT button is pressed, variable
memory editing is executed.
Once editing has been executed, the memorized
speed will be cleared. The initial speed will not be
cleared however.
9
The result of editing can be checked by pressing
PREVIEW/REVIEW button.
O
The content stored in the memory will be cleared in
a mode other than the variable memory mode.
Also, the memory will be cleared when the power
switch is turned OFF.
O
Phase adjustment is not made during playback to
the IN point of variable memory editing.
Therefore, depending on the VTR used as the
player and its speed setting, no guarantees are
made for the accuracy of the IN point.
O When variable memory editing is to be performed,
keep the speed set to within the speed range for
variable speed playback which can be guarantied
by the VTR used as the player.
Using the unit as a controller (deck-to-deck editing
mode recorder) to control the playback speed of the
VTR used as the player, editing can be performed in
speed variable mode.
$ Selecting the variable memory mode
When deck-to-deck editing (either the RECORDER
or PLAYER lamp lights) is to be performed, set the
initial speed (–1.0 to +2.0) by turning the search
dial with the SET button held down to transfer the
unit to variable memory mode.
$ Releasing variable memory mode
Press the RESET button while holding down the
SET button to release the unit from variable
memory mode.
The unit will also be released from this mode when
deck-to-deck editing operations are completed.
Variable memory editing operation
procedure
Variable memory editing operation can be performed
according to the following procedure.
Variable memory editing
SD955B
ON
OFF
POWER
DV
DVCPRO
DVCPRO 50
METER
L
R
FULL/FINE
MONITOR SELECT
HEADPHONES
MONITOR MIX A VOL SELECT INPUT SELECT PREVIEW/PREVIEW AUTO EDIT PREROLL
VIDEO
REC LEVEL
CH1
PB LEVEL
AUDIO
CH2 CH3 CH4 TC PRESET MENU SET DIAG SUPER REC INH INT TCG MODE CONTROL
ON
OFF
UNITY
VAR
COUNTER
RESET
A IN TRIM
SET
OUT IN
A OUT
CH1 CH4 CH2
INSERT
CH3
ASSEM VIDEO CUE TC STAND BY
EDIT
REW STOP
PLAY REC
PLAYER RECORDER
FF
JOG SHTL SLOW
TAPE
EE
ON REGEN
PRESET
EXIT OFF
REMOTE
LOCAL
1
3
2
1
Select the edit mode by pressing ASSEM button or
desired INSERT buttons.
2
Select VTR to be operated by pressing
RECORDER or PLAYER button.
3
Register IN/OUT point by using SET button and
IN/OUT buttons.
The OUT point of VTR used as the player cannot
be registered.