Philips BDP7200 - Manual (Page 35)

35 EN
C
onnec
tions
Pla
yback
F
unc
tion
S
etup
O
thers
In
tr
oduc
tion
Basic
S
etup
SETUPS
Use this feature to adjust the aspect ratio of the video
source which is different from your TV’s ratio to fit your
TV monitor without distorting the picture. Descriptions
of each setting are as follows:
Video
source
Your
TV
Option Description
16:9
4:3
4:3 Letter Box To enjoy 16:9
picture on 4:3
monitor:
16:9 picture is
scaled down until
the both sides of
the picture fits the
4:3 TV.
4:3 Pan & Scan To enjoy 16:9
picture on 4:3
monitor:
Both sides of the
picture are trimmed
to fit the 4:3 TV
without distorting
the aspect ratio of
the picture.
16:9
16:9
Widescreen To enjoy 16:9
picture on 16:9
monitor:
Select this setting
when you want to
enjoy 16:9 picture
on the 16:9 TV.
4:3
16:9
Squeeze To enjoy 4:3 picture
on 16:9 monitor:
Use this setting to
display 4:3 picture
on the 16:9 TV
without distorting
the aspect ratio of
the picture.
HOME “Settings” “Advanced Setup” “Video Output” “TV Shape”
HOME “Settings”
“Advanced
Setup”
“Video Output”
“HDMI Video
Resolution”
Set the resolution of the video signal being output from
the HDMI OUT.
You can select the desired “HDMI Video Resolution”
among the settings listed below:
“Auto”/“480p”/“720p”/“1080i”/“1080p”
When you make a selection, the TV monitor temporarily
goes blank and then comes back again. If it does not,
press [OUTPUT] to change the resolution or press and
hold [
B (PLAY)] on the front panel for 5 seconds to
change the setting back to its default.
•
Actual Output Resolution by Media:
Media BD
Setting in
the “HDMI
Video
Resolution”
Source
480/60i 720/60p 1080/60i 720/24p 1080/24p
480p 480/60p 480/60p 480/60p 480/60p 480/60p
720p 720/60p 720/60p 720/60p 720/60p 720/60p
1080i 1080/60i 1080/60i 1080/60i 1080/60i 1080/60i
1080p
1080/60p 1080/60p 1080/60p 1080/60p
1080/24
or 60p
(*)(**)
Auto The highest resolution supported by your
display device will be in effect automatically.
Media DVD DivX®
Photo
viewing
OSD-only
viewing
Setting in
the “HDMI
Video
Resolution”
Source
480/60i 60,30,other
480p 480/60p 480/60p 480/60p 480/60p
720p 720/60p 720/60p 720/60p 720/60p
1080i 1080/60i 1080/60i 1080/60i 1080/60i
1080p 1080/60p 1080/60p 1080/60p 1080/60p
Auto Determine the rightmost resolution supported
by the display device automatically.
The frame rate and interlaced/progressive setting of
the data on Blu-ray Disc is the framerate and interlaced/
progressive setting of the primary video being played.
If no video is being played it is whatever frame rate was
set last by the BD middleware.
The frame rate and resolution of the component output
will follow that of the HDMI output, except when HDMI
resolution is 1080p (in which case the component
output will be at 480i).
Output from the VIDEO OUT will be always at 480/60i,
when supported.
(*) : 24 Hz is preferred, but if EDID shows that 24 Hz not supported, but
60 Hz is, then 60 Hz should be shown.
(**) : When frame rate is 24p, all analog output will be muted.
Note
The selected resolution must also be supported by
your display device.
If your TV and the unit is connected by a DVI cable
and if you select “Auto”, “480p” will be in effect
automatically.
Pressing [
B (PLAY)] on the front panel for 5 seconds
changes the setting back to its default. (“Component
Output” setting will also be reset to default (480i).)
Refer also to your TV’s manual.
•
•
•
•
•
•
•
•
TV Shape
HDMI Video Resolution
E5E10UD_EN.indb 35 E5E10UD_EN.indb 35 12/28/2007 9:25:55 AM 12/28/2007 9:25:55 AM