Land Pride RC5515 User Manual
Page 13
11
Section 1: Assembly & Set-up
5/29/13
RC5515 & RC6515 (540 RPM) RCM5515 & RCM6515 (1000 RPM) Rotary Cutter 318-721M
Section 1: Assembly & Set-up
•
Three duplex outlets are required if the wings are
raised and lowered independently. (Requires
Hydraulic Wing Control Kit on page 29 to raise wings
independently.)
•
If the tractor does not have the necessary number of
duplex outlets, there are control valve kits available to
add outlets. See “Hydraulic Accessories” on page 28
for a complete description of the kits.
Before You Start
Read and understand the operator’s manual for your
cutter. An understanding of how it works will aid in the
assembly and setup of your cutter.
It is best to go through the Pre-Assembly Checklist
before assembling the cutter. Speed up your assembly
task and make the job safer by having all needed parts
and equipment readily at hand.
Torque Requirements
See “Torque Values Chart” on page 50 to determine
correct torque values when tightening hardware. See
“Additional Torque Values” at bottom of chart for
exceptions to common torque values.
Pre-Assembly Checklist
Check
Referenc
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on
hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose
parts are shipped with the machine.
Operator’s
Manual
Double check to make sure all parts, fasteners,
and pins are installed in the correct location.
Refer to the Parts Manual if unsure. By double
checking, you will lessen the chance of using a
bolt incorrectly that may be needed later.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed during assembly. Keep parts
separated.
Operator’s
Manual
330-323M
Parts Manual
330-323P
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Operator’s
Manual
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Make sure all red and amber reflectors are
correctly located and visible when machine is in
transport position.
Make sure all tires are inflated to the specified
psi air pressure and all wheel bolts and axle
nuts are tightened to the specified torque.
Tractor Requirements
Horsepower
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used. If the tractor is too small, it can be pushed
around and/or flipped over by the weight of the cutter.
Too large a tractor can damage the cutter.
Horsepower Rating . . . . . . . . . . . . . . . . . .50-250 HP
Drawbar Set-up
Refer to Figure 1-1:
Maintain proper distance, dimension “A”, between center
of drawbar hitch pin hole and end of tractor PTO shaft.
Hitch Type . . . . . . . . . . . . . . . . . . . . . . . . . . Draw Bar
540 RPM & 1 3/8" @ 1000 RPM Rear PTO Speed:
“A” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14"- 16"
“B” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8" - 10"
“C”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" to 22"
1 3/4" @ 1000 RPM Rear PTO Speed:
“A” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" - 20"
“B” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10" - 12"
“C”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" to 22"
PTO to Drawbar Distance
Figure 1-1
PTO Speed
Rear PTO Speed:
Model RC5515 & RC6515. . . . . . . . . . . . . 540 RPM
Model RCM5515 & RCM6515 . . . . . . . . . 1000 RPM
Hydraulic Outlets
The number of tractor hydraulic duplex outlets is
dependent upon how the Rotary Cutter is set-up.
•
Two duplex outlets are required if the wings are raised
and lowered simultaneously. (Factory standard)
IMPORTANT: PTO damage may occur if distances
“A” and “B” are not properly maintained.
IMPORTANT: A PTO adaptor should not be used.
Using a PTO adaptor can damage the PTO.
22273