Land Pride RC5015 - Manual

1 © Copyright 2007 Printed
Before You Start
Your Baffle/Shredder Kit for Comer Gearbox (S/N
325493+) is exclusively designed for your Land Pride
RC5015 Rotary Cutter. Please read these installation
instructions and your RC5015 Rotary Cutter Operator’s
Manual thoroughly before beginning. Especially read
information relating to safety concerns. Also included in
the Operator’s Manual is important information on
operation, adjustment, troubleshooting, and
maintenance for this attachment (some manual sections
do not apply to all accessories).
General Information
These assembly instructions apply to the following
RC5015 Baffle/Shredder Kit Accessories listed below:
318-395A ASSY.BAFFLE/SHRD COMER RC50-60
Further Assistance
Your dealer wants you to be satisfied with your new
Baffle/Shredder Kit for Comer Gearbox (S/N 325493+).
If for any reason you do not understand any part of this
manual or are not satisfied with the service received, the
following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
[email protected]
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
Assembly Instructions
A detailed listing of parts for this accessory kit is provided
on page 4. Use the list as a checklist to inventory parts
received. Please contact your local Land Pride dealer for
any missing hardware.
!
CAUTION
Lower implement to the ground, put tractor in park, turn off
engine, engage parking brake, and remove key before
performing installation of the Baffle/Shredder Kit.
Baffle/Shredder Installation
Refer to Figure 2 on page 3:
1.
Before the Baffle/Shredder Kit can be installed,
eight - 17/32" dia. holes must be drilled in the center
deck. Refer to page 3 for hole locations.
Refer to Figure 1 on page 2:
2.
Assemble Front Mounting Plate (#11) and Rear
Mounting Plate (#2) to Center Baffle (#4) with
carriage bolts (#3) and flange nuts (#1) as shown.
3. Mount this assembly in the holes that were drilled in
the center deck using carriage bolts (#3) and flange
nuts (#1).
4. Remove blade carrier assembly from gearbox output
shaft. Keep the hardened washer (#12) slotted hex
nut (#13) and cotter pin (#14) to use in step #4.
5. Install Blade carrier (#9) to gearbox output shaft.
Installing blade carrier without the blades attached
will be much easier. Reinstall washer (#12) and nut
(#13). The slotted nut should be torqued to 550 ft./
lbs. The cotter pin (#14) should be installed in the nut
with legs securely bent around the nut.
6. Assemble blades (#7) and (#8) to the blade carrier
(#9). Torque blade bolt lock nut (#10) to 450 ft./lbs.
7. Repeat steps 3, 4 and 5 for Right Hand and Left
Hand Deck.
RC(M)5015/6015 with Comer Gearboxes (S/N 325493+)
Baffle Kit Assembly Instructions and
Shredder Kit Assembly Instructions
07/02/07
Manual No. 318-314M