Kenmore 790.4658 - Manual (Page 27)

ENGLISH
27
Scratches or abrasions on
cooktop surface.
Metalmarks.
Brown streaks or specks.
Areas of discoloration with
metallic sheen.
Oven control beeps and
displays F1, F3 or F9
Oven light does not work.
Poor baking results.
Fan noise during cooking
operation.
Flames inside oven or
smoking from vent.
Oven smokes excessively
during broiling.
Self-cleaning cycle does
not work.
Soil not completely
removed after self-
cleaning cycle.
Coarse particles such as salt or sand between cooktop and utensils can cause scratches. Be
sure cooktop surface and bottoms of utensils are clean before usage. Small scratches do not
affect cooking and will become less visible with time.
Cleaning materials not recommended for ceramic-glass cooktop have been used. See
“Ceramic Glass Cooktop Cleaning & Maintenance” section under General Care & Cleaning.
Cookware with rough bottom has been used. Use smooth, flat-bottomed cookware.
Sliding or scraping of metal utensils on cooktop surface. Do not slide metal utensils on
cooktop surface. Use a ceramic-glass cooktop cleaning cream to remove the marks. See
“Ceramic Glass Cooktop Cleaning & Maintenance” section under General Care & Cleaning.
Boilovers are cooked onto surface. Use razor blade scraper to remove soil. See “Ceramic
Glass Cooktop Cleaning & Maintenance” section under General Care & Cleaning.
Mineral deposits from water and food. Remove using a ceramic-glass cooktop cleaning
cream. Use cookware with clean, dry bottoms.
Electronic control has detected a fault condition. Press CLEAR to clear the display and stop
beeping. Program oven again. If fault recurs, record fault number. Press CLEAR and contact
Sears or other qualified service agency.
Replace or tighten bulb. See “Changing Oven Light” in this owner’s Guide for instructions.
Many factors affect baking results. Make sure the proper rack position is used. Center food
in the oven and space pans to allow air to circulate. Allow the oven to preheat to the set
temperature before placing food in the oven. Try adjusting the recipes’ recommended
temperature or baking time. If you feel the oven is too hot or cool, see “Adjusting the
Oven Temperature” section in this Use and Care Guide.
A cooling fan may automatically turn on and off to cool internal parts. It is normal, and the
fan may continue to run after the range has been turned “OFF” but may also stop
immediately to turn “ON” after a while.
Excessive spillovers in oven. Set self-clean cycle for a longer cleaning time.
Excessive spillovers in oven. This is normal, especially for pie spillovers or large amounts of
grease on the oven bottom. Wipe up excessive spillovers before starting the self-clean cycle. If
flames or excessive smoke are present, stop the self-clean cycle and follow the steps under
"Stopping or Interrupting a Self-Cleaning Cycle" in this Use and Care Guide.
Control(s) not set properly. Follow instructions under “Setting Oven Controls” in this Use
and Care Guide.
Make sure oven is opened to Broil Stop Position.
Meat too close to the element. Reposition the rack to provide proper clearance between the
meat and the element. Preheat broil element.
The insert on broiler pan wrong side up and grease not draining. Always place insert on the
broiler pan with ribs up and slots down to allow grease to drip into pan.
Grease has built up on oven surfaces. Regular cleaning is necessary when broiling
frequently. Old grease or food spatters cause excessive smoking.
Control(s) not set properly. Follow instructions under “Self-Cleaning” in this Use and Care
Guide.
Self-cleaning cycle was interrupted. Stop time must be 3 to 4 hours past the start time.
Follow steps under "Stopping or Interrupting a Self-Cleaning Cycle" in this Use and
Care Guide.
Hand clean bottom, front top of oven, frame or door area outside oven seal before the self-
cleaning is started. These areas are not in the self-cleaning area, but get hot enough to
burn on residue. Burned-on residue can be cleaned with a stiff nylon brush and water or
nylon scrubber. Be careful not to damage the oven seal by attempting to clean it.