Remote control configuration for vcr/dvd, Vcr brand list dvd brand list – Sony KP-44DX2 User Manual
Page 34
34
Remote Control Configuration for VCR/DVD
In it’s default condition this remote control will operate the basic functions of this Sony TV, Sony DVDs and most Sony VCRs. To
control VCRs and DVDs of other manufacturers (and some Sony VCR models), please complete the following steps:
• Before you start, look up the 3 digit code for your brand of DVD or VCR from the list below. On those brands that have
more than one code, enter the first code number.
• Sony will endeavour to update the software according to market changes. Therefore, please refer to code table included
with the remote control for latest code set.
VCR Brand List
DVD Brand List
Brand Code
Brand
Code
SONY (VHS)
301, 302, 303, 308, 309
SONY
001
SONY (BETA)
303, 307, 310
AIWA
021
SONY (DV)
304, 305, 306
DENON
018, 027, 020, 002
AIWA
325, 331, 351
GRUNDIG
009, 028, 023, 024, 016, 003
AKAI
326, 329, 330
HITACHI
025, 026, 015, 004
DAEWOO
342, 343
JVC
006, 017
GRUNDIG
358, 355, 360, 361, 320, 351
KENWOOD
008
HITACHI
327, 333, 334
LG
015, 014
JVC
314, 315, 322, 344, 352, 353, 354, 348, 349
LOEWE
009, 028, 023, 024, 016, 003
LG
332, 338
MATSUI
013, 016
LOEWE
358, 355, 360, 361, 320, 351
ONKYO
022
MATSUI
356, 357
PANASONIC
018, 027, 020, 002
ORION
328
PHILIPS
009, 028, 023, 024, 016, 003
PANASONIC
321, 323
PIONEER
004
PHILIPS
311, 312, 313, 316, 317, 318, 358, 359
SAMSUNG
011, 014
SAMSUNG
339, 340, 341, 345
SANYO
007
SANYO
335, 336
SHARP
019, 027
SHARP
324
THOMSON
012
THOMSON
319, 350
TOSHIBA
003
TOSHIBA
337
YAMAHA
018, 027, 020, 002
To do this:
1
Press the Media Selector button on the remote control repeatedly until the required green light (VCR or
DVD) is lit.
If Media Selector is on TV position, code numbers will not be stored.
2
Before the green light goes out, press and hold the YELLOW button for approximately 6 seconds until the
green light starts flashing.
3
Whilst the green light is flashing, enter all three digits of the code for your brand of VCR or DVD using
the number buttons on the remote control.
If your selected code is entered correctly, all three green lights will be lit momentarily.
4
Turn on your VCR or DVD and check that the main functions work.
• If your device is not working or some of the functions do not work please check that you entered
the correct code set or try the next code listed against the brand.
• Your brand codes may be lost if weak batteries are not replaced within a few minutes. To reset
your brand of DVD or VCR please repeat the above steps. A small label is added inside the battery
door to allow you to record your brand codes.
• Not all brands are covered and not all models of every brand may be covered.
5
When you wish to use the remote control to operate the TV again, press the Media Selector button until
the TV green light illuminates. Don’t forget to select VCR or DVD using the Media Selector button every
time you wish to operate that equipment with this remote control.
Additional Information