Samsung CLP-650 Series User Manual
Page 61
Solving Problems
7.15
Engine Fuser
Low Heat Error
The temperature in
the fuser is abnormally
low.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Engine Fuser
Over Heat Error
The temperature in
the fuser is abnormally
high.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Engine Fuser
Inverter Error
A problem has
occurred in the Fuser
in the printer.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Engine LSU
Error
A problem has
occurred in the LSU
(Laser Scanning Unit)
in the printer.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Install
[Color] Toner
The indicated color
toner cartridge is not
installed in the printer.
Install the corresponding color
toner cartridge.
Install
Transfer Belt
The paper transfer belt
is not installed in the
printer.
Install the paper transfer belt.
Invalid Toner
[Color]
An invalid toner
cartridge has been
installed.
Only install Samsung toner
cartridges, designed for your
printer. Or install the toner
cartridge into each proper
cartridge slot. If you have
installed an Samsung toner
cartridge or into each proper
caartridge slot and this error
still occurs, contact an
authorized service agent.
Invalid
Transfer Belt
An invalid paper
transfer belt has been
installed.
Only install Samsung paper
transfer belts, designed for
your printer. If you have
installed an Samsung paper
transfer belt and this error still
occurs, contact an authorized
service agent.
Jam0 In Tray1
Jam0 In Tray2
Jam0 In MP Tray
A paper jam has
occurred in or near the
indicated tray.
Remove the jammed paper
from the corresponding tray,
referring to page 7.4.
Jam
In Exit Area
A paper jam has
occurred in the paper
exit area.
Remove the jammed paper
from the printer, referring to
Jam
Inside Printer
A paper jam has
occurred inside the
printer.
Open the access door and
remove the jammed paper
from the printer, referring to
Message
Status
Do this...
Load
[Size] In Tray1
Load
[Size] In Tray2
Load
[Size] In MP
The paper size
specified in the printer
properties does not
match the paper you
are loading.
Load the correct paper in the
tray.
Low Density
The amount of the
toner which is spread
on the paper transfer
belt for adjusting auto
color registration is
very small, so that the
printer does not
recognize the toner
during auto color
registration.
Replace the toner cartridge(s)
with a new one. See page 6.4.
If you still have the same
problem, contact a service
representative.
Left Fan Error
A problem has
occurred in the Left
Fan of the printer.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Main Motor
Error
A problem has
occurred in the
development motor of
the printer.
Unplug the power cord and
plug it in again. If the problem
persists, call for service.
Memory
Overflow
The printer does not
have enough memory
to print the current
job.
An error has occurred
in the firmware
program of the printer.
The job automatically clears
and the printer returns to
Standby Mode.
Lower the print resolution and
try again.
Paper Empty
[Size] In Tray1
Paper Empty
[Size] In Tray2
Paper Empty
[Size] In Mp
Paper Empty
[Size] In
Manual
The paper tray has run
out of paper.
Load paper in the paper tray.
See page 4.2.
Photo LED error
During auto color
registration, the
printer does not
recognize the photo
LED in the paper
transfer belt assembly.
Contact a service
representative.
Message
Status
Do this...