Sharp DV-NC150U - Manual (Page 7)

Setup
Setup
If you cannot play back a disc which bears one of the
marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs
recorded in other color systems such as PAL cannot be
played back.
*2: Certain DVD-Video discs do not operate as described in this
manual due to the intentions of the disc’s producers.
*3: This label indicates playback compatibility with DVD-
RW discs recorded in VR mode (Video Recording
Format).
This player cannot play the DVD-RW that supports CPRM
(Contents Protection for Recordable Media).
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompati-
ble recording conditions, characteristics of the recorder or
special properties of discs.
*6: You can play back discs which bear the marks above. If
you use nonstandardized discs, this unit may not play
them back. Even if they are played back, the sound or
video quality will be compromised.
DVD-Video
* 1,2,4,6
* 1,2,3,4,5,6
* 1,2,3,4,5,6
* 4,6
* 4,5,6
or
DVD-R
DVD-RW
DVD+R
DVD+RW
Audio CD
CD-R
CD-RW
Digital video
(MPEG2)
Digital audio
or
MP3
Region code Mark (logo)
Playable
discs
Recorded
signals
Disc size Disc types
12 cm
or
8cm
12 cm
or
8cm
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3 Chapter 4
Example
Group 1 Group 2
Track 1 Track 2 Track 5 Track 6 Track 3 Track 4
Example
Track 1 Track 2 Track 5 Track 6 Track 3 Track 4
Digital audio
MP3
About the Video Cassettes and Discs
Playable Discs
Unplayable Discs
¡On the following discs, only the sound can be heard (picture cannot be viewed).
CDV, CD-G
¡NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM, CD-I, Photo CD, Video CD, DVD with region codes other than 1 or ALL,
DVD-ROM for personal computers,
CD-ROM for personal computers
¡On the following disc, the sound MAY NOT be heard.
Super Audio CD
¡Any other discs without compatibility indications.
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press the OUTPUT button on the VCR/DVD so that the VCR OUTPUT light is lit.
• If “VCR” light does not appear on the display of this unit, press the VCR/TV button on the remote control.
4) Press the PLAY button once.
5) After a few seconds, press the PLAY button on the VCR/DVD for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
In this case, “ch04” will appears on the front panel.
• When a picture does not appear on the TV screen, repeat step 4.
6) Press the STOP button to stop playback.
RF Output Channel
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
– 7 – EN
Use only cassettes marked with this unit.
Playable Video Cassettes
Hint Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, press the PLAY
button on the VCR/DVD for 3
seconds again.
Hint Hint
• Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer can-
not be delivered.