Sharp DV-NC150U - Manual (Page 15)

VCR Functions
EN
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
DIGITAL AUDIO OUT
COAXIAL ANT-OUT
ANT-IN AUDIO OUT
DVD DVD/VCR VCR S-VIDEO OUT COMPONENT VIDEO OUT AUDIO OUT
VIDEO OUT
AUDIO IN
VIDEO IN
L
L Y
C B
C R
L
R R
ANT-OUT
ANT-IN
VCR DVD/VCR COMPONENT VIDEO OUT AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
L Y
C B
C R
L
R R
R
AUDIO OUT
VIDEO OUT
L
R Connect
1
Audio/Video cables
(supplied)
Round Coaxial cable
(supplied)
(Back of TV)
(Back of Recording VCR/DVD*) (Back of another source)
or
2
Connect
*Front input jacks are also available
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording
VCR/DVD.
3) Press the SPEED button on the remote control of the
recording VCR/DVD to select the desired recording
speed (SP/SLP).
4) Select the "L1" or "L2" position on the recording VCR/DVD.
• To use the input jacks on the back of this unit, select
"L1" position by pressing [0], [0], [1] on the remote
control or the SKIP/CH. (K
K /L L ) buttons.
• To use the input jacks on the front of this unit, select
"L2" position by pressing [0], [0], [2] on the remote
control or the SKIP/CH. (K
K
/L
L
) buttons.
5) Press the REC button on the recording VCR/DVD.
6) Begin playback of the tape in another source.
7) To stop recording, press the STOP/EJECT button on
the recording VCR/DVD, then stop playback of the tape
in another source.
Hint Hint
• For best results during dubbing, use the front panel controls whenever possible. The
remote control might affect another source’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio
cables are not recommended.
• You can use a video disc player, satellite receiver, or other audio/video component with
A/V outputs.
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
• “L2” input jacks are on the front of this VCR/DVD.
Copying a Video Tape
1 1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
B TV STEREO [ON]
SAP
MENU 1 1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
B AUDIO OUT
TV STEREO [ON]
SAP
MENU
MTS System (Multi-Channel Television Sound)
Select “TV STEREO” or
“SAP”
2 2 To exit the menu.
CLEAR/
C.RESET 2 2
AUDIO OUT
B HIFI [ON]
MONO
Select “HIFI” or “MONO”
When You Receive or Record a
Program Broadcast in MTS
When You Play Back a Tape
Recorded in Hi-Fi Stereo
• When you receive a broadcast on
the VCR, you can check the type
of the broadcast by pressing the
DISPLAY button.
• When "TV STEREO" or "SAP"
selection is valid, select them by
following steps. This selection is
needed when you record the pro-
gram.
• SAP means Second Audio
Program (usually second lan-
guage).
Type of
broadcast
Regular
(monaural audio)
Bilingual
broadcast
Stereo &
Bilingual
broadcast
Stereo
broadcast
Display on the
TV screen
-None-
STEREO
STEREO
SAP
SAP
STEREO/SAP
Selection
-Invalid-
-Invalid-
TV STEREO
(main audio program)
SAP
(second audio program)
TV STEREO
(stereo main audio program)
SAP
(second audio program)
• If you have connected a stereo TV to
this VCR/DVD, select "STEREO".
• If you have connected a monaural TV
to this VCR/DVD, select "MONO".
STEREO Your Selection
Type of recorded tape
non Hi-Fi tapes
Hi-Fi tapes
recorded in
Hi-Fi stereo
Hi-Fi tapes
recorded second
audio program
Hi-Fi tapes
recorded main
audio program
MONO
Monaural
L+R
Main audio
program
Second audio
program
Monaural
R-channel L-channel
R
Main audio
program
Second audio
program
Monaural
L
Main audio
program
Second audio
program
3 3 To exit the menu.
CLEAR/
C.RESET
– 15 –
VCR VCR VCR VCR
or
or
or
VCR VCR
• If there is a power failure or the VCR/DVD has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a tape is not in the VCR/DVD or does not have the record tab, the TIMER and
lights flash and timer recording cannot be performed.
Please insert a recordable tape.
• If a tape ends during timer recording, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER and
lights flash. (If the DVD power is off, the VCR will become STANDBY status).
• When all timer recordings are finished, the TIMER and lights will flash.
• When timer recordings are set, theTIMER and lights will appears. To use the VCR as usual until the time for the recording, press the
SUBTITLE/T-SET button so that the TIMER and lights disappear. Press the VCR/TV button to choose the VCR position. Select either
VCR or DVD mode, then continue with the other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the TIMER and lights are on or flashes.
• You can use the DVD player while the TIMER and lights are on or flashes, or during a timer recording. Press the POWER button to
turn on the VCR/DVD. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as
described in this manual. You don’t have to set the TIMER off to use the DVD only.
Hint for Timer Recording