Sharp DV-NC150U - Manual (Page 12)

Hint Hint
• To go back one step, press the s button
(during the steps [2] to [7].)
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint Hint
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
press the CLEAR/C.RESET button.
– 12 – EN
Setup
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1 1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
POWER
3 3
CH 01
AUTO SET UP
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing
the K or L button. Then, press the B but-
ton.
3) Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the low-
est memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by press-
ing the K or L button. Then, press the B
button.
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing the K or L but-
ton. Then, press the CLEAR/C.RESET
button.
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using the SKIP/CH.
(
K/L) buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the B button once again.
Y Y es es Press the MENU
button to exit
• Refer to “Hint for Cable Box
or Satellite Box” section on
page 8.
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?
YES
NO
Turn on the unit for the first
time
TV Screen Remote Control
Clock Set Up
To Select a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
VCR VCR
Preparation for Use
5 5
4 4
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
6 6
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7 7
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select the current year
Select “AM” or “PM”
8 8 To exit the CLOCK SET
screen.
Select the current hour
Select the current minute
or
or
or
or
or
VCR
1 1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
MENU
2 2
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3 3
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
Select the current day
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
VCR VCR
or
or
or
VCR