Samsung BN68-01783B-00 - Manual (Page 69)

English - 69
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the
TV speaker.
1
Press the TOOLS button.
Press the ENTER button to select Anynet+ (HDMI-CEC).
2 Press the ▲ or ▼ button to select Receiver.
Press the ◄ or ► button to select On or Off.
3 Press the EXIT button to exit.
¯
If your receiver supports audio only, it may not appear in
the device list.
¯
The receiver will work when you have properly connected
the Optical IN jack of the receiver to the Optical Out jack of the TV.
¯
When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack.
When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home
theater receiver. When the source is a digital component such as a DVD and is connected to the TV
via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
¯
When listening through the receiver, there are restrictions for using the PIP and audio-related menus.
¯
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power
cord or a power failure), the Select Speaker may be set to External Speaker when you turn the TV
on again. (see page 34)
Check Points before Requesting Service
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure to search devices
again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+. ■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet+ devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the TV mode.
(Note that the channel button operates only when a tuner-embedded Anynet+ device
is not connected.)
The message Connecting
to Anynet+ device…
appears on the screen. ■ You cannot use the remote control when you are configuring Anynet+ or switching to a
view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does
not play.
■ You cannot use the play function when Plug & Play is in progress.
The connected device is
not displayed. ■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search
Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables
may not support Anynet+ functions.
The TV programme cannot
be recorded.
■ Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output
through the receiver.
■ Connect the optical cable between TV and the receiver.
Return Adjust Move
View TV
Device List
Recording : DVDR
DVDR Operation
Receiver
◄ On ►
Setup
iu]_TWX^_ZiTl•ŽU•‹‰GGG]` YWW_TW`TY\GGG㝘㤸GXXa[XaWX