Sunfire III - Manual (Page 25)

User's Manual
25
GUIDE MENU
MODE MODE
EXIT INFO
SYSTEM
+10
POWER
3 1
6 4
9 7
ENT DIS
M3 M1
2
5
8
0
M2
PAGE FAV
MAIN
OFF
VOL CH
MUTE
PREV
CH
CD
AUDIO
MAIN
TAPE
AUX
ZONE2
TGIII
DVD
VCR
SAT
TV
CABLE
CHAPTER 3
Remote Control
Think of the TGIII remote control
as ten remotes in one. There are ten
DE VICE buttons, fi ve on either side
of the display, and each allows the
remote to operate one piece of equip-
ment.
From the factory, the device but-
tons are labeled: CD, TAPE, AUX,
ZONE2, TGIII, DVD, VCR, SAT, TV
and CA BLE.
Only the TGIII and ZONE2
buttons are pre-programmed, and
these allow the remote to operate
your TGIII. The remote can be set to
operate your other remote controlled
equip ment. This is done in three ways
from the hidden SETUP menu:
1. Entering a code from the tables at
the end of this manual
2. Stepping through the codes
3. Learning from your other remotes
See Remote Setup on page 27 for
more details.
LCD Display
The top line shows the present
device, mode or status, and it shows
when a remote command is being
transmitted. The bottom line shows
the page number, status and basic
in struc tions during programming.
The main part of the display
shows the labels of the ten DE VICE
buttons. You can change any label
and customize the remote to fi t your
sys tem. Note: this is not a touch-sen-
sitive screen, just a way of labeling
the device buttons on each side, and
showing in struc tions and status.
Contrast
The contrast of the display can be
changed by holding down the MAIN
button and pressing the joystick pad
UP or DOWN.
Light
The button on the right side of
the remote briefl y turns on the lights
for the buttons and display. Pressing
it again will turn it off. The number of
sec onds can be varied, or it can be
disabled.
Device Buttons.
Once you press a device button,
all the device buttons change label
and function to become buttons to
operate your device. There are two
pages per device, and you can move
be tween them using the PAGE button.
PAGE
Use this to jump to various display
pages. For example, if you press
the TGIII device button, the display
chang es to some show buttons which
control your TGIII. If you press PAGE,
the display will move to page 2, show-
ing more func tions for the TGIII.
MAIN
This button will return the re-
mote display back to the Main menu.
Depending on which mode you are
in, it may take two or more presses.
This will help you get back to the
Main menu if you ever get lost in the
menus.
FAV
This button allows you to step
through fi ve display pages of your
favorite TV and radio stations. These
can be set and re-labeled to suit.
Joystick Pad
This pad and surrounding buttons
are used to operate standard DVD
menus, and VCR and Tape transport
controls. In TGIII mode, if you press
MENU, the On Screen Display will ap-
pear and the joystick can be used to
select and adjust the various items.
LIGHT
MAIN
JOYSTICK
MACROS
M1, M2 and M3 Macros
These MACRO buttons can be
programmed to send out a se quence
of commands with a single press.
Batteries
The remote takes four AAA bat-
teries inside the rear compartment.
These should last about six months
in normal use, before a low-battery
warning appears.
LCD
DEVICE
Buttons
DEVICE
Buttons
PAGE
IR WINDOW
FAV