JVC DR-MH50S - Manual (Page 72)

72
EN
SUBSIDIARY SETTINGS
DISPLAY SET
8
SUPERIMPOSE ^ OFF / AUTO
When this function is set to AAUTOB, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (
A pg. 20)
OFF:
To turn off superimposed indications.
AUTO :
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
NOTES:
● Even when ASUPERIMPOSEB is set to AOFFB, you can display
the various operational indicators by pressing ON SCREEN. To
clear the operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to
set
ASUPERIMPOSEB to AOFFB before starting. (A pg. 63)
● When you select AAUTOB, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8
BLUE BACK ^ OFF / ON
When this function is set to AONB, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals,
set this function to
AOFFB.
8
DIMMER ^ BRIGHT / DIMMED
You can change the brightness of the front display panel.
BRIGHT :
Normally select this.
DIMMED :
To dim the front display panel. (Blue lamp on the front display
panel is turned off.)
8
POWER SAVE ^ OFF / ON
When this function is set to AONB, you can reduce the power
consumption while the unit is turned off.
NOTES:
● During Power Save mode ^
^ the front display panel will be turned off.
^ the Just Clock function (A pg. 77) does not work.
● Power Save does not work when ^
^ the unit is in the Timer mode.
^ the unit’s power is turned off after timer recording or Instant
Timer Recording.
^ the Automatic Satellite Programme Recording mode is
engaged. ( A pg. 49)
^ AL-2 SELECTB is set to ADECODERB, ASAT VIDEOB or ASAT
S-VIDEO B. (A pg. 65)
● It takes some time for the unit to complete initialisation after you
turn on the unit power, with
AWAKE UPB blinking on the front
display panel.
8
ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in
10 different languages. Although Auto Set Up selects the language
automatically (
A pg. 19), you can change the language setting
manually as required.
For details, refer to
AOn-screen Language SetB (A pg. 20).
If you connect the unit and TV with Component Video Connection
(
A pg. 16), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
1
Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator ( q) lights on the front display panel if
Progressive scan mode has been established. ( A pg. 12)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
● When the progressive mode is set, be sure to set AL-1 OUTPUTB
to ACOMPONENTB (A pg. 64). Progressive scan is output only
from [COMPONENT VIDEO OUT] connector.
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video
material.
● Scan mode cannot be set while menu screen is displayed.
● When the Progressive scan mode is engaged, no video signal is
output from [L-1 IN/OUT] connector.
Scan Mode Set
ATTENTION:
Your TV needs to be compatible with PAL Progressive.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
PROGRESSIVE SCAN
CABLE/SAT
DVD TV