JVC LVT1002-012B - Manual (Page 16)

13
When operating the receiver
using the remote control,
always set the mode selector
to AUDIO/TV/VCR/DBS.
RX-ES1SL
Basic operations
ANALOG
SUBWFR
VOL
L R
DVD MULTI DVD (DVD DIGITAL)
DBS (DBS DIGITAL) VCR TV (TV DIGITAL)
FM AM (Back to the beginning)
2
Select the source to play
On the front panel:
Turn SOURCE SELECTOR until the source name
you want appears on the display.
The source indicator corresponding to the selected source lights in
red.
• As you turn SOURCE SELECTOR, the source changes as follows:
From the remote control:
Press one of the source selecting buttons.
• Each time you press FM/AM, FM and AM changes alternately.
DVD MULTI: Select the DVD player using the analog discrete
output mode (5.1 channel reproduction). To enjoy
the DVD MULTI playback, see page 32.
DVD (DIGITAL) * : Select the DVD player.
DBS (DIGITAL) * : Select the DBS tuner.
VCR: Select the VCR.
TV (DIGITAL) * : Select the TV tuner.
FM: Select an FM broadcast.
AM: Select an AM broadcast.
* Selecting the analog or digital input mode
When you have connected the DVD player, DBS tuner, or TV tuner
using both the analog connection and the digital connection methods
(see pages 8 to 12), you need to select the correct input mode.
• You can select the digital input only for sources which you have
selected digital input terminals for. (See “Setting the digital input
(DIGITAL IN) terminals—DIGITAL IN” on page 20.)
From the remote control ONLY:
Press ANALOG/DIGITAL INPUT to select the analog
or digital input mode.
• Each time you press the button, the input mode alternates between
the analog input (“ANALOG”) and the digital input (“DGTL AUTO”).
DGTL AUTO: Select for the digital input mode. The receiver
automatically detects the incoming signal format,
then the digital signal format indicator (DOLBY D,
DTS or LPCM) for the detected signals lights up.
ANALOG*: Select for the analog input mode.
* Initial setting
NOTE
You cannot select the digital input mode when selecting “DVD MULTI”
as the playing source.
ANALOG
SUBWFR
VOL
L R
1
Turn on the power
Press STANDBY/ON (or AUDIO on the remote
control).
The STANDBY lamp goes off. The current source indicator lights in
red. The name of the current source (or station frequency) appears on
the display.
Current volume level is shown here.
Current source name appears.
To turn off the power (into standby)
Press STANDBY/ON again (or AUDIO on the remote control).
The STANDBY lamp lights up.
NOTE
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
STANDBY / ON STANDBY
DIMMER SETTING ADJUST SURROUND
DVD MULTI DVD DBS VCR TV FM / AM
SET / TUNER PRESET SOURCE SELECTOR MASTER VOLUME
PHONES / MULTI JOG
OPEN/CLOSE
DVD VCR DBS TV
DVD VCR DBS TV
DVD MULTI
TV VOL CHANNEL
TUNING TUNING FM MODE
MEMORY
TOP MENU
CHOICE
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L R SURR
BASS BOOST A.POSITION SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100+
BASS TREBLE
ECHO
SUBTITLE RETURN RESERVE TITLE/GROUP
ON
SCREEN
MENU
VOLUME
FM/AM TV/VIDEO MUTING
AUDIO
HOME CINEMA CONTROL CENTER
BASS TREBLE PROGRESSIVE
AUDIO/TV
/VCR/DBS
KARAOKE
DVD
KARAOKE SOUND
KARAOKE
VOCAL EFFECT
KEY
KEY
1 2 3
4 VFP
INPUT
TONE
TEST EFFECT DECODE
5 6
7 8 9
10
3D
0 +10
ENTER
CONTINUED ON THE NEXT PAGE
EN13-15RX-ES1&XV-NK58[A]f 03.6.6, 11:54 13