JVC XL-R5000BK - Manual (Page 17)

12
Englis
h
Concerning the CD numbers and play status display
The display shows for each CD tray whether or not a CD has been
inserted as well as the play status of the CD.
The CDR section can be used to play back CDs, CD-R, and CD-
RW.
1
Press the EJECT 0 button to open the CDR disc
tray.
2
Load a disc in position and close the tray.
• When a CD-R or CD-RW is loaded in the CDR for the first
time, OPC (Optimize Power Control) is performed. This proce-
dure requires anywhere from 10 seconds up to a minute to per-
form. Once OPC has been performed, the unit stores the
information for that disc in memory (occasionally some older
data will be erased and OPC may need to be performed again in
these cases).
• When a CD-R or CD-RW is loaded in the CDR, the unit deter-
mines the format of the disc, whether it is finalized or not, and
then determines whether OPC (Optimize Power Control) has
been performed for the disc or not. At this time, OPC is also
performed if necessary. The length of time required for this unit
to perform the necessary operations depends on the type and
status of the disc.
• When “UPDATE OPC” is displayed, the indicator lights
and the 3 and disc format indicator flashes.
3
Press the CDR CONTROL 3 button to select the
CDR function and start playback at track 1.
• Playback is automatically stopped at the end of the last track on
the disc.
• Unfinalized CD-R and CD-RW may be played back using the
CDR. Unfinalized discs cannot be played back using the 3-CD
changer.
To stop CDR playback
• Pressing the CDR CONTROL 7 (stop) button at any point dur-
ing playback stops the playback and the total track number and
play time appear in the display.
• When an unfinalized CD-R or CD-RW is loaded in the CDR
and the EJECT
0 button is pressed to open the CDR disc tray,
“FINALIZE?” appears in the display window. If you do not
wish to finalize the disc at this time, press the EJECT
0 button
again. For more information on finalization, see page 29.
To stop CDR playback temporarily
• Pressing the CDR CONTROL
8 (pause) button at any time dur-
ing playback pauses the playback. Press the 3 button to resume
playback.
• When playback is paused, the 8 indicator lights in the display.
Note
Before finalization of the disc is performed, when you playback of
the disc is started from the stop mode or at a track that is skipped
forward or reverse to etc., the very beginning of the track may cut.
The buttons on the remote control can be used to control playback
of both the 3-CD changer and CDR. When using the remote con-
trol, be sure to point the remote control correctly at the remote con-
trol sensor on the main unit when pressing the buttons.
1
Press the CD or CDR button to select the
function.
CD button: To control discs in the 3-CD changer
CDR button: To control the disc in the CDR
While a CD is playing, this lights in
sequence, and blinks in the pause mode.
It goes off when “NO DISC” is displayed to
indicate that a disc has not been loaded.
The CD on the CD tray for which this has
lighted is selected.
CDR Playback Operations
MIX BALANCE
STANDBY
PHONES LEVEL
MAX MIN
MULTI JOG
+ –
POWER
REC LEVEL
1 2
3
XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER
7 8
REC
Using the Remote Control to
Control Playback
1 2 3
4 5 6
7 8
10 +10
9
PLAY MODE REPEAT SET CANCEL
CONTROL
PITCH 0
PITCH +
PITCH – SHIFT
REMOTE CONTROL
RM-SXLR5000J
REC MUTING
REC
DISPLAY SYNCHRO CD REC
CD EDIT FINALIZE MENU
POWER
CD 1
CD 2
CD 3
CD CDR 1
2
CD 1, CD 2, CD 3
XL-R5000.book Page 12 Wednesday, March 29, 2000 6:37 PM