JVC RX-E12B - Manual (Page 20)

16
Basic settings
Operating procedure
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1 again.
Ex.: When setting DIGITAL IN 1 terminal.
1
Press SETTING.
MULTI JOG now works for the setting operation.
2
Turn MULTI JOG until the item you want to set
appears on the display.
• As you turn MULTI JOG, the setting items change as
follows:
3
Press SET.
The current setting of the selected item appears.
4
Turn MULTI JOG to select the appropriate
setting.
Your setting is stored.
5
Press SET.
6
Repeat steps 2 to 5 to set other items if
necessary.
Setting the speakers
Setting subwoofer information—SUBWOOFER
Each time the receiver turns on, the receiver detects the
subwoofer connection and automatically changes the setting of
the subwoofer.
When you want to change the setting manually, select either one
below.
SUBWFR : YES Select when you have connected a subwoofer.
The subwoofer indicator ( S . WFR ) lights up on the
display. You can adjust the subwoofer output level
(see page 21).
SUBWFR : NO Select when you have disconnected a
subwoofer.
Selecting this changes the front speaker size to
“LRG” (see below).
NOTE
You need to change the setting each time you turn on the receiver
if you want to change the subwoofer information set automatically.
Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker), SURRND
SPK (surround speakers)
Register the sizes of all the connected speakers.
LRG (large) Select when the cone speaker size is larger than
12 cm.
SML (small) Select when the cone speaker size is smaller than
12 cm.
NO Select when you have disconnected a speaker.
(Not selectable for the front speakers.)
Initial setting: SML for all speakers*
* When “SUBWOOFER” is set to “SUBWFR : NO,” the front
speaker size is fixed to “LRG” (and you cannot select “SML”).
NOTES
• If you have selected “SML (small)” for the front speaker size,
you cannot select “LRG (large)” for the center and surround
speaker sizes.
• If you change the center and/or surround speaker size either
from “NO” to “SML” or “LRG,” or from “SML” or “LRG” to “NO,” the
distance and output levels set by Smart Surround Setup will be
ineffective.
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
CENTER SPK SURRND SPK
FRNT R DIST CENTER DIST
(Back to the beginning)
SUBWOOFER FRONT SPK
DIST UNIT FRNT L DIST
SURR L DIST SURR R DIST
DUAL MONO CROSS OVER
SUBWFR OUT VIRTUAL SB
LFE ATT MIDNIGHT M.
AUTO SURRND AUTO MODE
DIGITAL IN1 DIGITAL IN2
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
DVR/DVD VIDEO
VCR TV
EN14-19RXE11S_12B[B]f.p65 08/12/2004, 15:00 16