MITSUBISHI ELECTRIC WD-62628 - Manual (Page 31)

Chapter 2. Connecting 31
Computer with an HDMI Monitor
Output
Figure 13
An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
Connect an HDMI cable from HDMI 2 on the TV
back panel to the PC’s HDMI output. HDMI devices
provide video and audio through this cable, so no other
connection is required.
57#BDL1BOFM
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
1 2
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1 2
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¸
'
,INK ¸
INPUT
PC - 60Hz VGA, W-VGA,
SVGA, W-SVGA, XGA, 1280 X 720
RIGHT
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¸
'
,INK ¸
1$XJUI)%.*0VUQVU
)%.*
Figure 13. Connecting a Computer with an HDMI Monitor
Output
Connecting a Computer with an HDMI or DVI Monitor Output
Computer with a DVI Monitor Output
Figure 14
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and
audio cables are required. These are not included with the TV.
They may be available at your local electronics retailer.
1. Connect the DVI-to-HDMI cable (recommended) (or
DVI/HDMI adaptor with an HDMI cable) from the PC
DVI output to HDMI 2 on the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI device
for best performance.
2. Connect a set of audio cables from AUDIO OUT on
the PC back panel to INPUT/DVI Analog Audio 2 on
the TV back panel. The red cable connects to the R
(right) channel, and the white cable connects to the L
(left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require connecting
to an analog input first, in order to view on-screen
menus and select DVI as the ouput. Please review
your equipment instructions for DVI connectivity and
compatibility.
"6%*0065
-&'5
3*()5
1$XJUI%7*0VUQVU
$6)
57#BDL1BOFM
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI Analog Audio
1 2 VIDEO
AUDIO-
LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1 2
IEEE 1394 INPUT/ OUTPUT
Net Command
IR EMITTER ¸
'
,INK ¸
INPUT
PC - 60Hz VGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720
COMPONENT COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
11 22
Y
Pb
Pr
AUDIO- LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI Analog Audio
1 VIDEO
AUDIO-
LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1
IEEE 1394 INPUT/ OUTPUT
Net Command
IR EMITTER ¸
'
,INK ¸
INPUT
%7*UP)%.*$BCMF
)%.*
"VEJP
Figure 14. Connecting a Computer with DVI Monitor
Output
CAUTION: To ensure continued FCC
compliance, the user must use a
shielded video interface or HDMI cable
with bonded ferrite cores at both ends
when using the PC input.
IMPORTANT
To view PC video on the TV:
• Activate the PC option in NetCommand. You
can do this during initial NetCommand setup
(in the Device Setup screen), or at any time
afterwards by using the NetCommand Add
function.
• See Appendix A for signal compatibility.