MITSUBISHI ELECTRIC WD-62628 - Manual (Page 24)

2 Chapter 2. Connecting
Additional connection cables are
not provided with the TV. They are
available at most electronics stores.
IMPORTANT
Connecting a Wall Outlet Cable or Cable Box
Wall Outlet Cable
(can be used with a CableCARD™)
Figure 1
It is very important to connect the incoming cable
for your primary viewing source to ANT-1, especially
for CableCARD™ use and to download TV Guide On
Screen® listings.
1. Connect the primary incoming coaxial lead cable to
ANT 1/MAIN on the TV back panel.
2. For an optional secondary antenna source, connect
an antenna (or cable) to ANT 2/AUX.
3. If you have subscribed to a CableCARD™ service,
the CableCARD can now be inserted into the
CableCARD SLOT. Using a Phillips screwdriver,
remove the CableCARD cover screws. Insert the
CableCARD, then replace the cover and screws. The
top of the card should face in the direction the CARD
TOP arrow indicates.
Additional CableCARD information is on page 23.
Detailed TV Guide On Screen information is in the
separate User’s Manual.
0QUJPOBM4FDPOEBSZ
"OUFOOBPS$BCMF
1SJNBSZ8BMM
0VUMFU$BCMF
$BCMF$"3%5.4-05
DPWFSSFNPWFE
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
DIGITAL
AUDIO
OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
5P"/5."*/ 5P"/5"69
57CBDLQBOFM
TFDUJPO
Figure 1. Wall Outlet Cable
Standard Cable Box
(cable box, other than an HDTV cable box; this setup
allows two-channel PIP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.
Note: See page 30 to connect an HDTV cable box.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the standard cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
5. After the cable box is connected to ANT-2 AUX as
shown, use the NetCommand menu Change option
to change the default connection for the cable box,
go to the RF Connection for Cable screen and do the
following:
a. Check the RF check box.
b. For antenna, select ANT-2.
c. For Channel, select the channel to which the TV
must be tuned for your cable box. The default
channel is 3.
When this setup is complete, you can use the TV remote
control to change channels on the cable box.
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT
CableCARD™ USE WITH ANT 1 CARD TOP
*/ 065
*/
065
065
5808
" :41-*55&3
57CBDL
QBOFM
TFDUJPO
*ODPNJOH
$BCMF
$BCMF#PYCBDL
QBOFMTFDUJPO
3'4QMJUUFS
5P"/5."*/ 5P"/5"69
Figure 2. Connecting a Cable Box
Note: To use a cable box connected to ANT-2 as shown
above, you must make the noted NetCommand changes.
The changes are required to change the NetCommand
cable-box default connection (Component-1) to the
actual connection (ANT-2).