beautypg.com

Learn – Marantz SR8001 User Manual

Page 69

background image

66

ENGLISH

• If the copying fails in the middle of the

copying process, ERROR is displayed on
the remote control.

Check and perform steps 1 to 7 again.

11.

Once copying is completed, press the M button

on both remote controls.

SETUP

SETTING THE LIGHTING TIME

• The LCD lights up when the LIGHT buttons are

pressed. The LCD remains lit while the pressed
button is held down, and it goes off when the
button is released.

• The LCD continues to light up if another button

is pressed while it is lit or if pressed within two
seconds after the light goes off.

• The lighting time can be set in one-second units

from 0 to 60 seconds.

The LIGHT buttons have light-absorbing properties
that enable them to store light. If the buttons are no
longer illuminated in a dimly lit environment, bring the
buttons near a fl uorescent lamp or other light source
for a suffi cient amount of time. This should illuminate
the buttons again.
• The LIGHT buttons consist of a LIGHT1 and

LIGHT2 button, and they both perform the same
operation.

The factory default lighting time is set to 15
seconds.

This example shows how to set the lighting time to
20 seconds.

PAGE

1 2

2 3 4

LEARN

1 2 3 4

LEARN

1 2 3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

2.

Press

the

> button to display the second page

SETUP menu.

3.

Press

the

D1 (LIGHT) direct button .

The LIGHT is displayed on the LCD

4.

Press

the

3

or

4

cursor button to set the

lighting time.

5.

Press

the

OK cursor button to enter the lighting

time.

6.

Once the setting is finished, press the M

button.

SETTING THE MACRO INTERVAL TIME

When a macro program is executed, control signals
are transmitted in sequence. This transmission
interval (interval time) can be set in 0.5-seconds units
from 0.5 to 5 seconds.
If the interval time is set in this Setup mode, the
interval times for all programmed macros are
changed. If necessary, use EDIT (see page 64) in the
macro program to change the individual transmission
times.
The factory default setting for the transmission
interval is 1 second.

This example shows how to set the interval time to
5 seconds.

PAGE

1 2

2 3 4

LEARN

1 2 3 4

LEARN

1 2 3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

2.

Press

the

> button to display the second page

SETUP menu.

3.

Press

the

D2 (I-TIME) direct button.

4.

Press

the

3

or

4

cursor button to set the

interval time.

Holding down the cursor button fast-forwards the

time indicator.

5.

Press

the

OK cursor button to enter the interval

time.

6.

Once the setting is finished, press the M

button.

ADJUSTING THE DISPLAY CONTRAST

The contrast of the LCD can be adjusted. Adjust
for maximum visibility according to your viewing
environment.

PAGE

1 2

2 3 4

LEARN

1 2 3 4

LEARN

1 2 3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

2.

Press

the

> button to display the second page

SETUP menu.

3.

Press

the

D3 (CONT) direct button .

4.

Press

the

3

or

4

cursor button and set the

display contrast for maximum visibility.

The adjustment has 10 levels.

The factory default setting for the contrast is the fi fth
level.

5.

Press

the

OK cursor button to enter the display

contrast.

6.

Once the setting is finished, press the M

button.

This manual is related to the following products: