Marantz SR8001 - Manual (Page 53)

50
ENGLISH
PRESET SCAN
2 3 1
OK
VOL CH
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
CH
MUTE
4.
AMP AUX2 AUX1 TAPE
TUNER CD CD-R MD
1 2 LIGHT
Learning Remote Controller RC8001SR
1.
TUNER
D4
D5
D2
M
D1
D3
D5 2.
2.
5.
USE PAGE 2
D4
5 6 4
8
0
9 7
MEMO CLEAR
DISP OSD
THX
SLEEP 5.
CLEAR
(Using the remote control unit)
1.
Press the TUNER button twice within two
seconds on the remote.
2. Press the > button until PAGE2 is displayed
and press the P-SCAN (D4) on the remote.
“PRESET SCAN” appears on the front display
and then the preset station with the lowest
preset number is recalled fi rst.
3. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
4. You can fast forward the preset stations, press
the > button until PAGE4 is displayed and
press the P-SET+ (D4) continuously.
5. When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P-SCAN (D4) on the
remote.
RECALLING A PRESET STATION
DSS
AMP AUX2 AUX1 TAPE
TUNER CD CD-R MD
VCR DVD TV
1 2
LIGHT
Learning Remote Controller RC8001SR
1.
TUNER
OK
VOL CH
PREV MUTE
GUIDE
LIP.SYNC
CH
MUTE
2.
(Using the SR7001)
1. Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel.
(Using the remote control unit)
1. Press the TUNER button twice within two
seconds on the remote.
2. Press the > button until PAGE4 is displayed
3. Press the P-SET+ (D4) or P-SET– (D5) button
to tune in the deseired preset station.
Or enter the preset station number with the
numeric buttons.
MANUAL PRESET MEMORY
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
3.
2.
2 3 1
5 6 4
8
0
9 7
MEMO
DIG
DO
MultEQ ENTER MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
DIRECT
SURROUND SPEAKER MULTI
SD
L C R SL S SR LFE
DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
3. 2. 4.
(Using the SR7001)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3. Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4. Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote control unit)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
3. Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
PRESET MEMORY
With this unit you can preset up to 60 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
STANDBY
PHONES
READY INPUT SELECTOR
AV SURROUND RECEIVER SR8001
MultEQ ENTER MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/STANDBY
L C R SL S SR LFE DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ
PCM AAC
2. 4. 1. 3. 5. 2.
1. To select FM , press the BAND button on the
front panel.
2. While pressing the MEMORY button, press the
1 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3. Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5. Operation stops automatically when all 50
preset memory positions are fi lled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.