Marantz SR8001 User Manual
Page 51
48
ENGLISH
SPEAKER A/B
DIGITAL
VIDEO
S-VIDEO
AUX 1 INPUT
VOLUME
DOWN
MultEQ
ENTER
MENU
7.1CH INPUT
MULTI
A/B
T-MODE
MEMORY
CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
SPEAKER
MULTI
L
C
R
SL
S
SR
LFE
DIGITAL
SURROUND
V-OFF
ULTI
AUTO
TUNED
ST
SPKR A B
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SURR
DIRECT
AUTO
DISC 6.1
MT X 6.1
EQ
PCM
AAC
2
3
1
5
6
4
8
0
9
7
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
6
SPK-AB
SR7001 has speaker system - A and speaker
system- B for front L/R channels.
You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPK-
AB on the remote.
7.1 CH INPUT
The SR7001 is equipped for future expansion
through the use of Multi channel Super Audio CD
multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8001
E
MENU
PURE DIRECT
THX
7.1CH INPUT
MODE
AUTO
MULTI
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/STANDBY
DISP
MULTI
AUTO
TUNED
ST
SPKR A
SLEEP
SURR
DIRECT
AUTO
DISC 6.1
1.
2.
DIGITAL
R
L
VIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
READY
MultEQ
A/B
ODE
MEMORY
CLEAR
SPEAKERS
MIC
L
C
R
SL
S
SR
LFE
DIGITAL
SURROUND
M
4.
2
3
1
5
6
4
8
0
9
7
MEMO
CLEAR
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
4
7.1CH
2.
4.
3.
4.
2
CH.SEL
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press
the
7.1 CH INPUT button on the front
panel or press 7.1 CH on the remote to switch
the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –12 to +12 dB.
The subwoofer can be adjusted between –18
and +12 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOL buttons on the remote.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
on the remote.
Notes:
• When the 7.1 CH. Input is in use, you may not select
a surround mode, as the external decoder determines
processing.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8001
MEN
PURE DIRECT
THX
7.1CH I
MODE
AUTO
MULTI
PURE DIRECT
SURROUND
DSD
POWER ON/STANDBY
DISP
MULTI
AUTO
SLEEP
SURR
AUTO
LIP.SYNC
Depending on the image device (TV, monitor,
projector, etc.) connected to the SR7001, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR7001
to correct the time lag between the sound and image.
It can be operated with the “LIP.SYNC” and
1
and
2
cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYSNC feature turns OFF (0 ms) in
the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYSNC feature is automatically
restored.
2
3
1
5
6
4
8
0
9
7
MEMO
CLEAR
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
GUIDE
LIP.SYNC