Marantz SR8001 - Manual (Page 55)

52
ENGLISH
LISTENING TO XM SATELLITE RADIO
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must
fi rst select the input source on the SR7001.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8001
PURE DIRECT THX
MODE AUTO M
PURE DIRECT
SURROUND
DSD
POWER ON/STANDBY
DISP MULTI SLEEP AUT
1.
D4
D5
D2
M
D1
D3
D5
D3
USE PAGE 1
2.
2.
DSS
AMP AUX2 AUX1 TAPE
TUNER CD CD-R MD
VCR DVD TV
1 2
LIGHT
Learning Remote Controller RC8500SR
TUNER
1.
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
STANDBY
PHONES
READY INPUT SELECTOR
AV SURROUND RECEIVER SR8001
MultEQ
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/STANDBY
L C R SL S SR LFE DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
ENTER
2.
(Using the SR7001)
1. Turn the INPUT SELECTOR knob to select
“TUNER”.
2. Press the BAND button to select either XM or
DAB.
(Using the remote control unit)
1. To select tuner, Press the TUNER button twice
within two seconds on the remote.
2. Press the > button until PAGE 1 is displayed.
Select XM or DAB with the D3 button.
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
SOURCE
OFF ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5 USE PAGE 2 3 4
D1
1.
2.
1. Press the > button until PAGE 3 is displayed.
2. Press the D1 (DISP) button four times to
display the signal status on the front display of
the SR7001.
S I G N A L :
• The display changes as shown below according to
the receiving condition.
SIGNAL: ■■■■■■
SIGNAL: STRONG
(Signal strength is good)
SIGNAL: ■■■■
SIGNAL: MARGINAL
(Signal strength is Marginal)
SIGNAL: ■■
SIGNAL: WEAK
(Signal strength is poor)
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
3. Adjust the antenna location until signal strength
is good.
4. Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR7001 or the SCAN +
or SCAN – buttons of the remote control unit.
SOURCE
OFF ON/OFF POWER ON
D4
D5
D2
M
D1
D3
D5 USE PAGE 2
D2
D1
4.
4.
R8001
MultEQ ENTER MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
L C R SL S SR LFE
DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
4.
• The Radio ID is displayed.
X M O O O R A D I O I D
Note:
• If “ANTENNA” appears in the front panel display,
the XM Connect-and-Play antenna or Passport
system may not be connected to the XM terminal on
the rear panel of this unit properly.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
SOURCE
OFF ON/OFF POWER ON
D4
D5
D2
M
D1
D3
D5
D1
USE PAGE 2 3 4
1.
2.
1. Press the > button until PAGE 3 is displayed.
2. Select the information with the DISP (D1)
button.
Artist name/Song title
Channel category
Channel number/name
Signal Status
When the Channel number/name mode is displayed:
X M O 4 0 : D e e p T r c
4 0 : D e e p T r a c k s
(If text is more than 13 characters long, the text is
scrolled.)