Marantz SR4002/SR5002 - Manual (Page 50)

47
ENGLISH
PRESET MEMORY
You can store the desired channel in the Preset
Memory.
In addition to AM and FM, it is possible to preset 50
XM channels.
D
SETUP SIMPLE PURE
T-MODE
RROUND MEMORY DISPLAY
D
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
3. 2.4.
CAT
P.SCAN
CAT
T.MODE
+10
MULTI/
SPKR A/B CH/
INPUT
M-SPKR
MUTE
EX/ES VIRTUAL CS
VOLUME
dts
l/
OFF ON SET
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
SURROUND SLEEP DISPLAY
A/D
LIP SYNC/
CL
SOURCE
1 1 2 2 3 3
4 4 5 5 6 6
7 7 8 8 9 9
0 0
P.DIRECT
HT-EQ HT-EQ
MEMO MEMO
3.
2.
(Using the SR5002)
1. Tune into the desired channel.
2. Press the MEMORY button on the front panel.
”- -” (preset number) starts blinking on the
dispIay.
- - X M 0 4 0
3. Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
0 1 X M 0 4 0
4. Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1. Tune into the desired channel.
2. Press the MEMO button on the remote
controller. “- -” (preset number) starts blinking
on the display.
3. Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
CHECKING THE XM PRESET CHANNEL
The preset channel can be checked on the on screen
display.
CAT
T.MODE
1 2 3
4 5 6
7 8 9
0 +10 HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INPUT
T.TONE
/SET UP
M-SPKR
MUTE
EX/ES VIRTUAL CS
VOLUME
dts
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
A/D
LIP SYNC/
MEMO
BAND
CL
CAT CAT CH/ CH/
P.SCAN
INFO INFO 4. 5.
2.
REMOTE CONTROLLER RC5001SR
TAPE
BASS TREBLE
MD CDR CD
AMP AUX2 AUX1
DVD VCR DSS TV
TUNER TUNER 1. 3.
(Using the remote controller)
1. To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2. Press the BAND button to select XM band.
3. Press the TUNER button twice within two
seconds on the remote controller.
4. Press the INFO button. to view a list of tuner
preset channeI on the on screen display.
5. If there are 10 or more preset channel, Press
the INFO button. again.
XM PRESET LIST
NO. 1 XM010 XXXXXXXXXX
NO. 2 XM011 XXXXXXXXXX
NO. 3 XM015 XXXXXXXXXX
NO. 4 XM022 XXXXXXXXXX
NO. 5 XM125 XXXXXXXXXX
NO. 6 XM001 Preview
NO. 7 XM001 Preview
NO. 8 XM001 Preview
NO. 9 XM001 Preview
MAIN RETURN EXIT
Note:
The preset channel indication disappears in about 5
sec.
PRESET SCAN
CAT
T.MODE
4 5 6
7 8 9
0 +10
HT-EQ
MULTI/
SPKR A/B
M-SPKR
MUTE
EX/ES VIRTUAL CS
VOLUME
7.1CH IN
STEREO NIGHT M-CH ST
A/D
MEMO CL
CAT CAT CH/ CH/
P.SCAN
2. 5.
- TUNING PRESET - + +
REMOTE CONTROLLER RC5001SR
TAPE
BASS TREBLE
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
MD CDR CD
AMP AUX2 AUX1
DVD VCR DSS TV
TUNER TUNER
4.
1.
1. Press the TUNER button twice within two
seconds on the remote controller.
2. Press the P.SCAN.
3. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for about 5-10 seconds each.
The time changes by the received condition. No
stored preset number will be skipped.
4. Pressing the T button during prescanning
speeds up scanning.
Also, pressing the S button returns to the
previous preset station.
5. When the desired preset station is received,
cancel the preset scan operation by press the
P. SCAN button.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
DIGITAL VIDEO S-VIDEO AUX 1 INPUT
ETUP MPLE
T-MODE
MEMORY DISPLAY MUTE
VOLUME
DOWN
EXIT ENU BAND
CLEAR
ENTER
3. 2.
CAT
P.SCAN
CAT
T.MODE
1 2 3
4 5 6
7 8 9
0 +10
MULTI/
MENU
SPKR A/B
INFO
CH/
INPUT
M-SPKR
MUTE
EX/ES VIRTUAL CS
VOLUME
dts
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
A/D
LIP SYNC/
HT-EQ HT-EQ
MEMO MEMO CL CL 3.
2.
1. Recall the preset number to be cleared with
the method described in “PRESET SERCH
MODE”.
2. Press the MEMORY button on the front panel
or Press the MEMO button on the remote
controller.
3. The stored preset number blinks in the display
for 5 seconds. WhiIe blinking, Press the CLEAR
button on the front panel or CL button on the
remote controller.
4. “xx CLEAR” appears on the dispIay to indicate
that the specified preset number has been
cleared.
Notes:
• To clear all stored preset stations, press and hold
the CLEAR (CL) and the ENTER buttons for two
seconds.
• There are 50 preset channels prepared at the factory
default. The 50 channels are all set to “CHANNEL
001”. Each channel can be stored in the preset
memory. You can search for only the preset
channels.