Marantz SR4002/SR5002 - Manual (Page 20)

17
ENGLISH
LEARN MODE
This remote controller is capable of learning and
storing codes used by other remote controls that you
already own.
For codes which are not learned, the remote
controller will transmit either the Marantz preset
codes from the initial settings, or remote codes from
another manufacturer’s AV equipment which is set
by the customer.
The receiver sensor for the remote controller signals is
located at the top of the remote controller.
Notes:
• This remote controller is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
1. Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 0.05 m (2 inches).
SYST EM R EMO TE C ONT ROLL ER RC5 500S R
0.05 m
2. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE SET
CAT MULTI/
ENTER
INFO
M-SPKR
MENU
3. Select the SOURCE button to select the
SOURCE.
REMOTE CONTROLLER
TAPE TAPE
BASS TREBLE
MD MD CDR CDR CD CD
DVD DVD
AMP AMP AUX2 AUX2
VCR VCR
TUNER TUNER
DSS DSS TV TV
AUX1 AUX1
4. Select the button to be learned.
• LEARN indicator lights up.
1 2 3
4 5 6
T.MODE
INPUT
EX/ES VIRTUAL CS
dts
P.DIRECT
l/
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
5. Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
Notes:
• When the SEND indicator blinks once, repeat this
step.
• If the LEARN indicator fl ashes when the SEND
indicator is lit, then the button cannot be learned.
• When the memory of the remote controller is full,
the LEARN and SEND indicators blink once. If
you want to learn the code, you should erase other
learned button.
6. Repeat steps 4 and 5 to learn other buttons in
same SOURCE.
7. Repeat steps 3 to 6 to learn other SOURCE.
8. When you have finished programming the
remote controller, press the SET button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
SEND
dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
SOURCE
INPUT LIP SYNC/
LEARN
Notes:
• When the SEND indicator blinks once again,
the transmitting code is unavailable for remote
controller, or the transmitting signal is intercepted
by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
E R A S I N G P R O G R A M M E D C O D E S
(RETURNING TO INITIAL SETTINGS)
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
Erasing the code by buttons
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
CAT MULTI/
MENU
ENTER
INFO
M-SPKR
2. Select the SOURCE button to select the button
to be erased.
REMOTE CONTROLLER
TAPE TAPE
BASS TREBLE
MD MD CDR CDR CD CD
DVD DVD
AMP AMP AUX2 AUX2
VCR VCR
TUNER TUNER
DSS DSS TV TV
AUX1 AUX1
3. Press and hold down the SLEEP button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
4. To return the NORMAL mode, press the SET
button.
Erasing the code by SOURCE
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
CAT MULTI/
ENTER
INFO
M-SPKR
MENU
2. Press and hold down the SLEEP button and
press the learned SOURCE button twice to be
erased.
• LEARN indicator lights.
TAPE TAPE AMP
BASS TREBLE
CH-SEL V-OFF ATT.
MD MD CDR CDR CD CD
DVD DVD
AUX2 AUX2
VCR VCR
TUNER TUNER
DSS DSS TV TV
AUX1 AUX1 1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Erasing the all SOURCES
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
CAT MULTI/
MENU
ENTER
INFO
M-SPKR
2. Press and hold down the SLEEP button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
1 2 3
INPUT dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND SLEEP DISPLAY
LIP SYNC/
SOURCE
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.