Marantz SR4002/SR5002 - Manual (Page 25)

22
ENGLISH
ADVANCED CONNECTING
R R SR SR
C C
SW SW SBR SBR
MULTI. MULTI. OUT OUT
SL SL SBL SBL L L
R R L L
((AUX2 AUX2)) 7.1CH INPUT 7.1CH INPUT
L L SL SL C C SBL SBL
R R SR SR SW SW SBR SBR
RS-232C RS-232C SPEAKER C SPEAKER C OFF OFF ON ON
R R
L L
FM FM ((75 75)) GND GND AM AM ANTENNA ANTENNA
VC VCR DVD DVD TV TV IN IN
TV TV DVD DVD VCR IN VCR IN
S-VIDEO S-VIDEO
VIDEO VIDEO
PRE OUT PRE OUT
FRONT A OR B.CENTER. FRONT A OR B.CENTER. FRONT A FRONT A + + B : 8 OHMS B : 8 OHMS
FRONT FRONT B B
((AUX2 AUX2)) 7.1CH INPUT 7.1CH INPUT
L L SL SL C C SBL SBL
R R SR SR SW SW SBR SBR
R R
L L
R R SR SR
C C
SW SW SBR SBR
SL SL SBL SBL L L
PRE OUT PRE OUT
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
R L
L R
R L
L R
R L R L
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
R L R L R L
R L R L
L R
Power
Amplifer
DVD Audio player
or
Super Audio CD Multi
channel player
Center Front
Left Front
Right
Surround
Left Surround
Right
Subwoofer
Surround
Back Left Surround
Back Right
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 31.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.
CONNECTING THE REMOTE CONTROL JACKS
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the
back of other units (not the SR4002/SR5002) to
“EXT”.(EXTERNAL) to use this feature.
R R R R L L L L L L L L R R
IN IN
OUT OUT REMOTE CONT. REMOTE CONT. OPT OPT DIGITAL OUT DIGITAL OUT
C CR R // P PR R C CB B // P PB B Y Y C CR R // P PR R C CB B // P PB B Y Y
1 1
DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE VCR VCR DVD DVD AUDIO AUDIO DSS DSS IN IN OUT OUT
C CR R // P PR R C CB B // P PB B Y Y DSS DSS DVD DVD VCR IN VCR IN VCR OUT VCR OUT MONITOR OUT MONITOR OUT
MONITOR MONITOR OUT 2 OUT 2
INPUT INPUT 1 1
INPUT INPUT 2 2
AC IN AC IN
MODE MODEL NO. SR5002
FLASHER FLASHER IN IN
AC OUTLETS AC OUTLETS
120V 60Hz 120V 60Hz
SWITCHED SWITCHED
1.25A 150W 1.25A 150W CENTER CENTER SURROUND SURROUND SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER CENTER. FRONT A OR B.CENTER. FRONT A + : 8 OHMS B : 8 OHMS SPEAKER SPEAKER
SYSTEMS SYSTEMS
T FRONT B B FRONT FRONT A A
SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS
2 2 1 1
5 5 4 4
DC DC TRIGGER TRIGGER
3 3
INPUT INPUT 3 3
INPUT 1 INPUT 1
COMPONENT COMPONENT VIDEO VIDEO
IN IN
OUT OUT REMOTE CONT. REMOTE CONT.
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
1
RC OUT
2
DVD player CD recorder CD player
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1. Hold down the 7.1CH INPUT (SR4002) / MULTI
(SR5002) button and MENU button on the front
panel at the same time for fi ve seconds.
2. The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3. Press the 1 or 2 cursor button to change this to
“IR=DISABLE”.
4. Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5. To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.