Miller Electric DS-64M Swingarc - Manual (Page 29)

OM-1588 Page 25
8-5. Security
The security feature allows a mini-
mum and maximum range limit to
be defined for Trim, inches per min-
ute (IPM), and ShpArc (see Section
12).
When the security lock is Off, the
full range of values is available for
each parameter.
When the security lock is On, the
range of values available for each
parameter is the defined value plus
or minus the defined range.
For example, if the IPM value is de-
fined as 125, and the range is de-
fined as 50, the actual range of
available IPM is 75 to 175 IPM (125
minus 50, and 125 plus 50).
1
Card Display
2 Moving Line
Moving line is under value that can
be changed. Change program
number to access desired program.
3
Lock On/Off
Toggles security feature On or Off.
Definable values are displayed
when Lock On is selected. Use side
panel controls to change values.
4
Trim And Range Display
5 IPM And Range Display
6 ShpArc And Range Display
Definable Values (Standard
Motor):
Trim: 0−99 Range: 0−99
IPM: 50−780 Range: 0−780
ShpArc : 0−20 Range: 0−20
In the example displays, the
operator could change the value of
Trim to 55 and its Range to
± 10.
Also, the operator could change the
value of IPM to 225 and its Range to
±
100 IPM from programmed
values. If the range settings are left
at 0, the operator cannot change
values from those programmed.
.
The security feature works only when a data card is inserted.
S eq u e n c e
D ua l S c h d
C a r d
> S ec u r i t y
> P r o g 1
L oc k O f f
1
Press
Mode
Turn
Unit
On
Select
P r o g 1
>L o c k O f f
2
P r o g 1
>L o c k O n
T r i m 5 0
R a n g e 0
5 Times
Side Panel
Parameter
Select
Increase/
Decrease
P r o g 1
L o c k O n
>T r i m 5 0
R a n g e 0
Increase/
Decrease
L o c k O n
T r i m 5 5
>R a n g e 0
I P M 2 0 0
Increase/
Decrease
Increase/
Decrease
T r i m 5 5
R a n g e 1 0
> I P M 2 0 0
R a n g e 0
T r i m 5 5
R a n g e 1 0
I P M 2 2 5
>R a n g e 0
I P M 2 2 5
R a n g e 1 0
>S h p A r c 0
R a n g e 3
P r o g 1
L o c k O n
>T r i m 5 5
R a n g e 0
Side Panel
Parameter
Select
Side Panel
Parameter
Select
Side Panel
Parameter
Select
Side Panel
Parameter
Select
Increase/
Decrease
T r i m 5 5
R a n g e 1 0
I P M 2 2 5
>R a n g e 1 0 0
Side Panel
Parameter
Select
L o c k O n
T r i m 5 5
>R a n g e 1 0
I P M 2 0 0
T r i m 5 5
R a n g e 1 0
> I P M 2 2 5
R a n g e 0
3
4
5
>P r o g 1
L o c k O n
T r i m 5 5
R a n g e 1 0
Side Panel
Parameter
Select
6