Remote configuration options, Diagnostic options, Phone number memory options – Multi-Tech Systems MT5600BL-V.90 User Manual
Page 27: Diag
Chapter 3 - Using the Front Panel
27
Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide (S000276E)
R
R
R
R
Remote C
emote C
emote C
emote C
emote Co
o
o
o
onf
nf
nf
nf
nfig
ig
ig
ig
igur
ur
ur
ur
ura
a
a
a
at
t
t
t
tiiiiio
o
o
o
on Opt
n Opt
n Opt
n Opt
n Optiiiiio
o
o
o
ons
ns
ns
ns
ns
The following screens are used to configure remote configuration options. For more
information about remote configuration, see Chapter 5, “Remote Configuration.”
ENABLE/DISABLE R.C.
Use the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons to turn
remoteconfiguration on or off.
REMOTE CONFIG. PASSWORD.
Use to enter the remote con-
figuration password. To scroll through a list of digits and charac-
ters, press the
З
З
З
З
ЗЕ
Е
Е
Е
Е and И
И
И
И
И buttons. To go to the next position,
press the
Ж
Ж
Ж
Ж
Ж button. To back up or to exit without saving, press
the
Ж
Ж
Ж
Ж
Ж button several times. To save the password, press the
Enter
button.
Diag
Diag
Diag
Diag
Diagno
no
no
no
nost
st
st
st
stiiiiic Opt
c Opt
c Opt
c Opt
c Optiiiiio
o
o
o
ons
ns
ns
ns
ns
Use the following screens to turn loopback tests on and off.
ANALOG LOOPBACK.
Press the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons to start
the analog loopback test. The
TEST IN PROGRESS
screen
appears. To stop the test, press the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons again.
DIGITAL LOOPBACK.
Press the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons to start
the local digital loopback test. The
TEST IN PROGRESS
screen appears. To stop the test, press the
Ж
Ж
Ж
Ж
Ж and
Enter
but-
tons again. Same as the
&
T3
command.
REMOTE DIGITAL LOOPBACK.
Press the
Ж
Ж
Ж
Ж
Ж and
Enter
but-
tons to start the remote digital loopback test. The
TEST IN
PROGRESS
screen appears. To stop the test, press the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons again. Same as the
&
T6
command.
Note:
Digital Loopback and Remote Digital Loopback tests must be performed using AT Commands. The
LCD option to run these tests has been temporarily removed.
Pho
Pho
Pho
Pho
Phone Number
ne Number
ne Number
ne Number
ne Number Memo
Memo
Memo
Memo
Memor
r
r
r
ry
y
y
y
y Opt
Opt
Opt
Opt
Optiiiiio
o
o
o
ons
ns
ns
ns
ns
Use the following screens to list, enter, and dial stored phone numbers. Up to four
phone numbers can be stored. The number in memory location 0 is used for DTR
dialing, if DTR dialing is enabled. Note
:
Only 16 characters can be displayed at a time.
To display characters 17–30, press the
И
И
И
И
И button. To go to the previous screen, press
the
Е
Е
Е
Е
Е button. To go to the next screen, press the Ж
Ж
Ж
Ж
Ж button.
LIST PHONE NUMBERS.
Press the
Ж
Ж
Ж
Ж
Ж button several times to
display the phone number stored in each memory location.
ENTER PHONE NUMBERS.
Use to store up to four phone num-
bers in memory locations 0–3. Each number can have up to 30
characters. To scroll through a list of digits and characters, press
the
З
З
З
З
ЗЕ
Е
Е
Е
Е and И
И
И
И
И buttons. To go to the next position, press the Ж
Ж
Ж
Ж
Ж
button. To back up or to exit without saving, press the
Ж
Ж
Ж
Ж
Ж button
several times. To save the number, press the
Enter
button.
Same as the
&
Z=
commands.
DIAL STORED NUMBERS.
Press the
Ж
Ж
Ж
Ж
Ж and
Enter
buttons to
dial a stored phone number. Same as the
DS=
commands.