Maytag 110 - Manual (Page 31)

31
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
11 To Remove a Hotplate Burner Spark
Electrode
Remove the pan supports, burner heads and caps.
Remove the screw holding the electrode to the burner
body. Lift up the electrode and disconnect the lead.
Note
Take care to prevent the ignition wire from falling back
through the clearance hole.
Fit the lead to the new electrode and reassemble in
reverse order and check correct burner ignition.
12 To Remove an Oven Door
Open the oven door. Support the door and remove the
two screws that secure the upper hinge to the front frame
of the unit. Remove the door from the lower hinge by
lifting slightly and moving it outward. Re-assemble in
reverse order.
13 To Remove the Oven Outer Door Panel
Open the oven door. Remove the socket headed screws
at the sides of the door. Remove the outer door panel.
Remove the handle and fi t to the new door panel. Fit the
replacement panel to the oven inner door. Re-assemble
in reverse order.
14 To Remove the Door Latch
Remove the oven outer door panel – see 12. Remove
the fi xings that secure the latch assembly to the inner
door panel. Fit the replacement catch and re-assemble in
reverse order. Check correct operation of door.
15 To Remove the Oven Door Seal
Open the oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal diagonally
away from the door centre until that hook is released.
Proceed to the next hook and release it in a similar way,
and so on. Use force if the hooks are stiff, as the old seal
will be discarded.
When fi tting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
16 To Adjust the Oven Door Catch Keeper
Open the oven door and slacken the locknut at the
keeper base. Adjust the keeper inward or outward as
required, until the desired door operation is obtained. Re-
tighten the locknut.
17 To Remove the Hotplate Spark Generator
Disconnect the appliance from the electricity supply.
Pull the cooker forward to access the cover boxes at the
appliance rear. Remove the fi xings that secure the cover
and lift it clear. Undo the terminal connections noting
their positions. Undo the fi xings that secure the spark
generator and remove the device.
18 To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
Remove the hotplate - see 2. Remove the cover box and
disconnect all HT leads at the generator. Disconnect the
lead at the electrode. Pull the sleeved bundle of HT leads
up through the rear upright. Pull the appropriate lead
from the sleeve and push in the replacement. Replace
the leads in the rear upright. Re-connect the leads at the
generator and oven electrode. Re-assemble in reverse
order and check ignition.
19. To Remove Grill Element.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Remove the 4 terminals connected to the
elements noting their position. Remove grill pan from
grill chamber. From inside grill compartment remove
enamelled front shield from grill roof, 2 screws and
washers. Remove 2 screws and washers securing the
grill element front support. Remove 1 screw from each of
the grill elements and withdraw grill elements from grill
chamber. Fit new elements, reassemble in reverse order.
Check operation of grill.
20 To Remove the Warmer Chamber Element
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
the RH cooker side panel see 3.
The heating element is now accessible.
Disconnect element wires and pull the element pad out of
the side of the cooker and discard.
Take the new warming element and sandwich it between
the 2 pieces of card supplied with the kit.
Squeeze
the assembly together and feed into the gap between
the two ovens. Remove the two cards starting with the
top piece and taking care not to disturb the element.
Reconnect element wires.
Re-assemble cooker in the reverse order.