Maytag 110 - Manual (Page 30)

30
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Servicing
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS. TURN OFF THE GAS SUPPLY
Check the appliance is gas sound after completion of
service. When checking for gas leaks do not use washing
up liquid - this can corrode. Use a product specifi cally
manufactured for leak detection.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before commencing
servicing, particularly before removing any of the
following: - control panel, side panels, hotplate tray or any
electrical components or covers.
Before electrical re-connection, check that the appliance
is electrically safe.
Note - References to LH and RH oven apply as viewed
from the front.
1 To Remove the Control Panel
Disconnect the appliance from the electricity supply.
Pull off all the control knobs. Open the oven doors and
remove the 2 fi xing screws, one at each end, underneath
the control panel.
Pull off the push fi t control panel end caps at each end
and remove the end fi xing screws under the end cap.
Lift the control panel, pull forward and disconnect the
wiring from the rear.
Replace in reverse order.
2 To Remove the Hotplate top
Disconnect the appliance from the electricity supply. Pull
cooker forward to gain access.
Remove the control panel see 1. Remove the hotplate
burner caps and tops. If there are screws holding the
hotplate burners to the hotplate, remove them (not the
spark electrode fi xing screws). Remove the 2 hexagon
headed rear hotplate fi xing screws and the 3 front
hotplate fi xing screws. Lift the hotplate clear of the
appliance. Replace in reverse order.
3 To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
Remove the control panel – see 1. Remove the retaining
screw on the upper front edge and the two fi xings on
the rear or the side panel. Undo the lower retaining
screw situated below the edge at the panel front corner.
Remove the panel by pulling it away from the unit.
4 To Remove an Oven Neon
Remove the control panel – see 1. Hold the lens in
position at front of the panel and from the rear pull the
body of the neon out of the front lens. Hold the front
lens in position and from the rear of the control panel fi t
the new light to the lens. Replace parts in reverse order.
Ensure the replacement neon functions correctly.
5 To Remove the Clock
Remove the control panel - see 1.
Pull off the timer control button(s). Remove the timer/
mounting bracket assembly from the facia by removing
the fi xing screws. Remove the timer from its mounting
bracket by depressing the plastic lugs on the timer case,
at the same time pulling the unit forward. Reassemble in
reverse order. When replacing leads refer to the wiring
diagram. Check operation of timer.
6 To Remove a Thermostat
Disconnect the appliance from the electricity supply.
Remove the hotplate – see 2. Open the appropriate oven
door and remove the oven shelves.
RH oven
Remove the two fi xings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the
oven back panel.
LH oven
Remove the two screws holding the thermostat phial to
the oven fan cover at the rear of the oven. Pull the unit
forward to access the rear of the cooker. Remove the
both cover boxes by removing the fi xing screws and
lifting clear. Feed the thermostat capillary clear of the
oven. Disconnect the wires from the thermostat and undo
the two fi xings that secure the control to the mounting
plate. Fit the replacement and re-assemble in reverse
order. Ensure that the phial is clipped to the oven rear,
positioned centrally between the clips. Check that the
thermostat functions correctly.
7 To Remove an Oven element Thermal Cut-
Out.
Disconnect the appliance from the electricity supply. Pull
the cooker forward to gain access to the cover box. Undo
the cover screws and lift clear. The cutout is located on
the earth plate beside the oven element connections.
Disconnect the cutout wiring. Undo the fi xings that secure
the cutout to the earth plate and remove. Fit replacement
control and re-assemble in reverse order.
8 To Remove a Hotplate Tap
Remove the hotplate – see 2. Unplug the FSD lead from
the rear of the tap. Undo compression fi tting at the rear of
the tap. Remove the fi xings that secure the tap to the gas
rail. Disconnect the ignition switch wiring. Remove the tap.
Remove and discard the gasket seal. Fit new gasket seal
to replacement tap. Re-assemble in reverse order. Check
the appliance is gas sound. Check hotplate ignition.
9 To Change an Ignition Switch
Change the gas tap - see 7.
10 To Remove a Hotplate Burner Injector
Remove the hotplate - see 2. Remove the injector directly
from the burner body. Fit the appropriate injector. Re-
assemble in reverse order. Check the appliance is gas
sound.