Marantz SR5400U User Manual
Page 28
25
ENGLISH
ENGLISH
6.1 CH INPUT.
The SR5400 is equipped for future expansion
t h r o u g h t h e u s e o f M u l t i c h a n n e l S A C D
multichannel player or DVD-Audio player.
When this is selected, the input signals connected
to the L(front left), R (front right), CENTER, SL
(surround left), SR (surround right) and SB
(surround back) channels of the 6.1 CH. In jacks
are output directly to the front (left and right),
center, surround (left and right) and surround back
speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer)
jack.
When 6.1 CH. INPUT is selected, the last video
input used remains routed to the
Monitor Outputs
.
This permits simultaneous viewing with video
sources.
1.
Select a desired Video source to decide the
routed video signal to the
Monitor Outputs .
2.
Press the
6.1 CH INPUT
button on the front
panel or press
6.1 CH IN
on the remote to
switch the 6.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, use “6.1 Ch. INPUT LEVEL” in
the OSD menu system as desired.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 6.1
Ch. INPUT memory. (see to page 19)
4.
Adjust the main volume with the
MAIN VOLUME
knob or the
VOL
buttons on the remote.
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR5400 is sent to
the record outputs.
This means that any program you are watching or
listening to may be recorded simply by placing
machines connected to the outputs for
TAPE OUT,
CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT
in the record mode.
To record the input source signal you are currently
watching or listening to
1.
Select the input source to record by pressing
the corresponding
input selector
button.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the
TAPE OUT , CD-R/MD OUT,
VCR1 OUT, and DSS/VCR2 OUT
outputs for
recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and the
audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from a
compact disc player connected to CD IN and the
video from a video camera connected to AUX IN to
video cassette recorder connected to the VCR1
OUT jack.
1.
Press the
AUX
input source button to set
video output.
2.
Press the
CD
input source button to set audio
output.
3.
Now “CD” has been selected as the audio
input source and “AUX” as the video input
source.
Notes:
• If you change the input source during recording,
you will record the signals from the newly
selected input source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog .
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
400
MEMORY
TUNING
MODE
CLEAR
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
S-DIRECT
DISPLAY
A/D
6.1CH INPUT
VIDEO OFF
F/P
1.
2.
V SURROUND RECEIVER SR5400
MEMORY
TUNING
CLEAR
PHONES
ENTER
DSS/VCR2
AUX
VCR1
DVD
TV
CD-R
TAPE
S-DIRECT
A/D
6.1CH INPUT
VIDEO OFF
F/P
2.
OUND RECEIVER SR5400
MEMORY
TUNING
MODE
CLEAR
HONES
NTER
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
S-DIRECT
DISPLAY
A/D
6.1CH INPUT
VIDEO OFF
F/P
1.
MENU
OSD
SLEEP
MUTE
AMP
AUX
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
VOL.
VOL.
TV
1.
MAIN
MENU
OSD
SLEEP
MUTE
AMP
AUX
TUNER
CD
TAPE
CDR/MD
DVD
VCR1
DSS/VCR2
TV
VOL.
VOL.
TV
MAIN
2.
1.
To cancel the 6.1 Ch. INPUT setting, press the
6.1
CH INPUT
button on the front panel or press
6.1
CH IN
on the remote.
Notes:
• When the 6.1 Ch. Input is in use, you may not
select a surround mode, as the external decoder
determines processing.
• In addition, there is no signal at the record outputs
when the 6.1 Ch. Input is in use.
PTY
ATT
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
DSP
DTS
S-DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SETUP/
/A
/VCR
/ANT
/B
2.