Marantz SR5400U - Manual (Page 11)

8
ENGLISH RESETTING THE ALL CODE
1. Press and hold down the any function button
and press
SETUP until the indicator blinking
twice.
2. Press the code 9 - 8 - 1 .
The indicator will blink twice.
Then, RC5400SR will return to the factory
preset code.
Note:
• After this procedure, the selected function button
is set initial code and other function buttons are
set initial code too.
SCANNING THE CODE TABLE
1. Switch on the appliance which should be
controlled.
2. Press and hold down the function button for
appliance which should be controlled and
press
SETUP until the indicator blinking
twice.
3. Press the code 9 - 9 - 1 .
The indicator will blink twice.
4. Aim the remote control at the appliance and
slowly alternate between pressing
POWER
and the function button for the appliance.
5. Stop when the appliance turns off.
6. Press SETUP once to lock in the code.
CHECKING THE CODE
1. Press and hold down the function button for
appliance which should be controlled and
press
SETUP until the indicator blinking twice.
2. Press the code 9 - 9 - 0 .
The indicator will blink twice.
3. To view the code for first digit, press 1 once.
Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.
Note:
If a code digit is “0”, the indicator will not blink.
4. Repeat step 3 three more times for remaining
digits. Use
2 for the second digit, 3 for the
third digit, and 4 for the fourth digit.
PROGRAMMING THE REMOTE
CONTROLLER
The remote controller RC5400SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-
digit code or by scanning the codes until the
correct one is found. We recommend to using the
4-digit code. This mode is faster and more
reliable. The code scanning method should be
used only if you cannot find the code for one of
your appliances. The codes are listed at the end of
this book.
Important:
• Use the remote control buttons for programming,
not the buttons of the receiver or other
appliances.
• Some codes may be not match your equipment.
In this case, your equipment cannot be
controlled with this remote controller.
PROGRAMMING WITH THE 4-DIGIT CODE
1. Press and hold down the function button for
the appliance which should be controlled and
press
SETUP until the indicator blinks twice.
2. Press the 4-digit code for appliance (code
table at the end of this book)
3. When the procedure is successful, the
indicator will blink twice.
Note:
• If the indicator did not blink twice, then repeat
steps 1 through 2 and try entering the same code
again.
MENU OSD
SLEEP MUTE
AMP AUX
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
VOL. VOL. TV MAIN 1.
PTY ATT.
F.DIRECT DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN
6.1CH IN STEREO M-CH ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES DSP
DTS S-DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SETUP/
OK
+/A /VCR /ANT –/B
1.
2.
MENU OSD
SLEEP MUTE
AMP AUX
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
VOL. VOL. TV MAIN 1.
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN
6.1CH IN STEREO M-CH ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES DSP
DTS S-DIRECT AUTO 3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SETUP/
MENU OSD
OK
1.
2.
MENU OSD
SLEEP MUTE
AMP AUX
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
VOL. VOL. TV MAIN 2.
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN
6.1CH IN STEREO M-CH ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES DSP
DTS S-DIRECT AUTO 3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SETUP/
MENU OSD
OK
2.
6.
3.
MENU OSD
SLEEP MUTE
AMP AUX
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
VOL. VOL. TV MAIN
F.DIRECT DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN
6.1CH IN STEREO M-CH ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES DSP
DTS S-DIRECT AUTO 3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SETUP/
OK 1.
3.
4.
2.
Once you have found and the codes for your vari-
ous appliances, you may want to write them down
here.
TV
VCR
DSS
DVD
CD
TAPE
CDR
MD