Marantz SR5400U - Manual (Page 10)

7
ENGLISH
. Numeric buttons 1 to 9 / Surround mode
buttons
Numeric buttons
These buttons are used to enter figures in the selec-
tion of a tuner preset station and station name pre-
set or to set select a CD track number, etc. The func-
tions of these buttons are dependent on the function
button selected.
Surround mode buttons (when AMP mode is
selected)
These buttons are used to select the surround mode.
⁄0 P.SCAN (preset scan) button
(when TUNER mode is selected)
This button is used to start preset scan when
SR5400 is selected TUNER mode.
⁄1 0 / A/D button
0 button
This button is used to enter the number “0”
A/D button (when AMP mode is selected)
This is used to switch between the analog and
digital inputs.
⁄2 CONTROL buttons
These buttons are used when operating the CD
player, TAPE deck, etc.
The function of these buttons are dependent on the
function button selected.
For the controllable functions of each input function,
please refer to contrable function table on the page 10.
⁄3 ATT (attenuator) button
When the input signal is too high and the voice dis-
torts even while adjusting the SR5400 VOLUME
control, turn on this function. “ATT” is illuminated
when this function is activated.
The input level is reduced. Attenuator is invalid for
the output signal of “REC OUT”.
Note:
• This function is unavailable while the digital input
is selected.
⁄4 TREBLE UP ( ) /DOWN ( ) buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
⁄5 BASS UP ( ) /DOWN ( ) buttons
These buttons are used to adjust the tone control of
low frequency sound for left, right and subwoofer
speaker.
⁄6 MEMO button
Memory enable button for various preset functions.
⁄7 CLEAR button
This button is used to cancel for certain memory or
programming operations.
⁄8 DISPLAY button
Selects the display mode for the front display of the
SR5400.
⁄9 NIGHT button
Pressing this button prevents the Dolby Digital sig-
nal from playback at a loud voice. This function re-
duces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
¤0 S- (Source) DIRECT button
When this button is pressed, the tone control
circuit is bypassed.
¤1 SETUP / T.TONE button
(when AMP mode is selected)
Used to enter the test tone menu.
¤2 OSD button
(when AMP mode is selected)
When this button is pressed, the current setting is
displayed on the TV monitor.
¤3 SLEEP (sleep timer) button
This button is used for setting the sleep timer. It can
be operated the same way as the button on the unit.
¤4 TV VOLUME UP ( ) /DOWN ( ) buttons
These buttons increase or decrease TV’s volume.
REMOTE CONTROL
OPERATION
FUNCTION AND OPERATION
The provided remote control unit is a universal re-
mote controller. The
POWER button, numeric but-
tons and control buttons are used in common across
different input source components.
The input source controlled with the remote control
unit changes when one of the input selector but-
tons is pressed.
z Transmitting indicator
Lights up during a button is pressed and an infrared
signal is sending.
x (Main) POWER buttons
(when AMP mode is selected)
Press to switch the power of the SR5400 ON or OFF
after pressing the
AMP button.
c Input selector buttons/ FUNCTION
SELECTOR buttons (AUDIO/VIDEO INPUT)
These buttons are used to select a Audio or Video
source component. Press one of these buttons
once to change the function of the remote control.
Press same button within 2 seconds, the input func-
tion of the SR5400 is changed.
Note:
• CDR/MD button is set CDR function at initial. To
switch MD function, press and hold down CDR/
MD button and press 2 button.
• To return CDR function, press and hold down
CDR/MD button and press 1 button.
v MAIN VOLUME UP ( ) /DOWN ( ) buttons
Main volume control of the SR5400. The front, sur-
round, center and subwoofer channel volumes con-
trolled by these buttons simultaneously.
b MUTE button
Muting button of the SR5400. Press this button de-
crease the sound temporarily . Press this button
again to return to the previous sound.
When this button is pressed, “MUTE” indicator lights
up.
n MENU button
(when AMP mode is selected)
This button is used to enter the SETUP MAIN MENU.
m Cursor buttons ( , , , , OK)
Used to operate on-screen and other displays used
by receivers and other components.
See page 16.
, MENU OFF button
(when AMP mode is selected)
This button is used to exit from the SETUP MAIN
MENU.
OK
DISC/DECK
PTY ATT. –/B /VCR +/A /ANT
F.DIRECT DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN
6.1CH IN STEREO M-CH ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES DSP
DTS S-DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SETUP/
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP AUX
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
SYSTEM REMOTE CONTROLLER
RC5400SR
.
,
m
n
b
v ¤4
c
x
z
⁄0
⁄1
⁄2
⁄3
⁄4
¤2
¤1
¤0
⁄9
⁄8
⁄7
⁄6
⁄5
¤3