Genie 3681036666 - Manual (Page 8)

8
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
C
h
p
RoGRammiNG the
R
emote
C
oNtRol
Programming 1:
A To program one Button of a Remote Control (Figure 11):
• Locate Learn Button and Learn Indicator Light near
Terminal Block on Power Head (Figure 12) .
• Press and release Learn Button . Red Learn Indicator Light
will blink 2 times per second .
• Press Remote Control Button once within 30 seconds . Red
Learn Indicator Light will stay lit .
• Press Remote Control Button again . Red Learn Indicator
Light will go out, indicating that memory is stored .
• Press again to Activate Unit .
B Program each additional Remote using step A above .
a
CCeSSoRieS
Remote Control Operation
A Press Button on Remote Control . Garage door will move .
B Press Button again . Garage door will stop:
• The door automatically stops at the end of the
open or close cycle .
C Press Button again . Garage door will reverse .
WARNING
A moving garage door may cause serious injury or death .
• Keep people clear of opening while door is moving .
• Do not allow children to play with the Remote Controls .
If the Safety Reverse does not work properly:
• Close the door and disconnect the Opener using the
Emergency Release Cord .
• Do not use the door Opener, Remote Controls, or
Wireless Keypad .
• Refer to the door and door Opener Owner’s Manuals
before attempting any repairs .
Figure 12 Learn Code Button and Indicator Light .
(Located Lower Right Corner) .
OPEN
CLOSE
LEARN
CODE
BUTTON
LEARN
INDICATOR
LIGHT
Figure 11
1-Button and 3-Button
Compact Remotes
w/Docking Station
D There are several additional varieties of remote controls
available from your local dealer, some equipped with
a flashlight .
A Open garage door using Wall Console .
B Lay a 2” x 4” board flat in center of doorway (Figure 10) .
C Close door using Wall Console .
D Check that door stops and reverses within 2 seconds after it
contacts board:
• If door does not reverse, decrease Close Force until
door reverses (Figure 9) .
• If door still does not reverse, move Limit Switch
toward door .
E Check Safe-T-Beam® System operation:
• If beam is blocked, door
will not close .
NOTE
The door must contact the 2” x 4” board before the
Carriage activates the Close Limit Switch . If not,
readjust the Close Limit Switch .
C
h
S
ettiNG
C
oNtaCt
R
eVeRSe
f
uNCtioN
a
DjuStmeNt
2:
NOTE
Limit Switch and Force Adjustments must be completed before
checking the contact reverse function .
2” x 4” board
laid flat
Figure 10
Checking
Contact
Reverse
NOTE
• Each Remote Control must be programmed
separately .
• The Remote Controls will not close the garage with
malfunctioning Safe-T-Beam® System .
• Program Remote Controls, while at least 24” from
Antenna Wire .
• If the red Learn Indicator Light blinks rapidly,
programming stopped . Restart programming .
• Each Button on a multi-button Remote Control is
for a different Opener . Cannot use more than one
Button for same Opener .
• A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one
time . If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless
Keypad, see “To Erase All Receiver Memory .”
To Erase All Remotes from Power Head Memory
A Press and hold Learn Button on Power Head for 10 seconds
or until Learn Indicator Light goes out . Memory is erased:
• Program Remotes again as needed .
To Replace Remote Control Battery
A FOR NON-FLASHLIGHT MODELS
• Pop off the back of the transmitter .
– Use coin, pen, screwdriver or any similar device .
– Replace old Battery with new coin type battery .
• Replace back of remote.
B FOR FLASHLIGHT MODELS
• Slide open battery cover .
– Replace old Battery with new AAA battery .
• Replace battery cover.