GE Monogram MONOGRAM ZV950 - Manual (Page 2)

Safety Information
WARNING:
TO REDUCE THE RISK
OF FIRE, ELECTRICAL SHOCK OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact
the manufacturer.
B. Before servicing or cleaning unit, switch
power off at the service panel and lock service
panel to prevent power from being switched on
accidentally. If the service panel cannot be locked,
fasten a tag or prominent warning label to the
panel.
AVERTISSEMENT
POUR RÉDUIRE LE RISQUE D’INCENDIE, DE
CHOC ÉLECTRIQUE OU DE BLESSURES, IL FAUT
OBSERVER LES RÈGLES SUIVANTES :
A. Utiliser cet appareil uniquement de la manière
prévue par le fabricant. En cas de question,
consulter le fabricant.
B. Avant toute intervention ou nettoyage, couper
l’alimentation électrique au disjoncteur et
verrouiller le panneau du disjoncteur pour éviter
la mise sous tension accidentelle. S’il n’est pas
possible de verrouiller le panneau du disjoncteur,
attacher un placard ou une étiquette très visible
au panneau.
• For general ventilating use only. Do not use to
exhaust hazardous or explosive materials or vapors.
• Structural framing, installation work and electrical
wiring must be done by qualified person(s)
in accordance with all applicable codes and
standards including fire-rated construction.
• Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back
drafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such
as those published by the National Fire Protection
Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
• Local codes vary. Installation electrical connections
and grounding must comply with applicable codes.
In the absence of local codes, the vent should be
installed in accordance with National Electrical
Code ANSI/NFPA 70-1990 or latest edition.
CAUTION:
To reduce risk of fire and to
properly exhaust air, be sure to duct air outside–Do
not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces or garages.
PRUDENCE
–Il faut prendre soin
d’installer un conduit vers l’extérieur pour réduire
le risque d’incendie et pouvoir évacuer l’air
correctement. Il ne faut pas évacuer l’air dans
l’espace entre les parois d’un mur, un plafond
ou un grenier, un espace sanitaire ou un garage.
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT
– Save these instructions
for local inspector’s use.
•
IMPORTANT
– Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
with your Owner’s Manual for future reference.
• Skill Level – Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time – 1 to 3 hours.
• Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the Warranty.
For Monogram local service in your area,
1.800.444.1845.
For Monogram service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
CAUTION:
Due to the weight and size of these vent hoods,
and to reduce the risk of personal injury or damage
to the product, TWO PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION.
PRUDENCE
À cause du poids et de la taille de ces hottes,
et pour réduire le risque de blessures et de
dommages, IL FAUT DEUX PERSONNES POUR
FAIRE L’INSTALLATION CORRECTEMENT.
WARNING:
To reduce the risk of fire or electrical shock, do not
use this range hood with any external solid-state speed
control device. Any such alteration from original
factory wiring could result in damage to the unit
and/or create an electrical safety hazard.
AVERTISSEMENT
Pour réduire le risque d’incendie ou de choc
électrique, il ne faut pas utiliser cette hotte avec
un régulateur de vitesse électronique externe. Toute
modification de ce type du branchement d’usine peut
endommager l’appareil ou créer un risque de choc
électrique.
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.