FieldServer FS-8704-09 SNMP - Manual (Page 34)

FS-8704-09 SNMP Driver Manual Page 34 of 39
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 9042 Toll Free: (888) 509 1970 email: [email protected]
Appendix C. Driver Error Messages
Message Description/Action
SNMP:#01 Err. Response report
err=%d
A response from the remote device reports an error. The message
is good but inside the message there is a field reporting an error.
Consult the vendor for the meaning of the printed SNMP error
number.
SNMP:#02a/b Err. Could not
read SNMP response version
The driver found an error in the message structure preventing it from
extracting the SNMP version number. See msg #05 for follow up
actions.
SNMP:#03a/b Err. Version.
Expected=1 Rcvd=%d
This driver only supports SNMP version #1. See msg #05 for follow
up actions
SNMP:#04a Err. Extract Int
Failed. Index=%d
SNMP:#04b Err. Expected INT.
Found NULL. Index=%d
The driver is extracting an integer value from the SNMP message
but the field was incorrectly formatted. Formatting can be checked
using Ethreal
4
SNMP:#05 Err. Parse Failed.
MD=%s Msg Buffer
The driver is attempting to process a SNMP message that is not
correctly formatted; contains an error or contains unsupported
SNMP elements. Immediately after the message has been printed
the driver does a hexadecimal dump of the message.
If you see this message rarely and data is being transferred correctly
then ignore it. If it is repeated or affects data transfer then take a log
and call tech Support. This message is usually preceded by a
message which provides a more specific clue as to why the parse
failed.
4
SNMP:#10 FYI. NuDesign MIB
File=%s created. (Tier=%d)
SNMP:#10 FYI. Custom MIB
File=%s created. (Tier=%d)
SNMP:#10 FYI. MIB File=%s
created. (Tier=%d)
These messages do not require any corrective action provided that
they report what you expected. They are printed for confirmation
only.
SNMP:#11 Err. Can’t open
MIBHead.ini. Producing std MIB
file
The configuration has told the driver to build a customized MIB file.
This requires that a file called MIBHead.ini is present on the
FieldServer. Refer to the configuration manual and Appendix A.3 for
more information.
SNMP:#12 Err. Bad MD length -
defaulting to 1 A MD was found where the length was not specified or specified as
zero. Specify the length setting it to one.
5
SNMP:#13 Err. Max=255
number of TRAP map
descriptors exceeded
The default maximum number of trap Map Descriptors is 255.
SNMP:#14 Err. SNMP_TRAP
map descriptor must have OID
specified
SNMP:#15 Err. Passive_Client
map descriptor must have OID
specified
You must specify the ‘SNMP_OID” parameter on a Map Descriptor
used for a trap. Read Appendix A for more information on Traps
5
SNMP:#16 unknown
SNMP_Read_Method value: %s
The only permitted value for the SNMP_Read_Method is
‘walk’Error! Bookmark not defined.
SNMP:#17 Err. Diagnostic 1
The driver has executed an internal diagnostic. If this message is
printed please call Tech Support.
4
Refer to Enote 63 on the Website for more information.
5
Edit the configuration file, downloaded the modified file to the FieldServer and restart the FieldServer for
the changes to take effect.