Yamaha EMX120CD - Manual (Page 29)

TIME
A
PROG
B C D
+ I0
E
CD TUNER
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
PRESET
INPUT
MUSIC PROGRAM
STANDBY/ON
DISPLAY SLEEP
ECHO
FLAT
LEVEL KARAOKE
VOLUME
DISC SKIP STOP PLAY/PAUSE
TUNER CD
TEST CENTER/REAR
/DELAY
OPEN/CLOSE REPEAT RANDOM MODE
E-21
English
COMPACT DISC PLAYER OPERATION
Program play
You can program up to 20 tracks in any desired order.
1
Load discs and close the disc table.
2
When in the stop mode, press the PROG button to
prepare for programming.
*
“PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc will begin flashing.
3
If necessary, select a desired disc by pressing the DISC
SKIP button.
*
Just after you change the disc, this unit reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
step, “WAIT” appears on the display and your
operation is canceled.
4
Use the track number input buttons to select the desired
track number.
*
The selected track number and the total play time of
the programmed tracks will light up on the display, and
soon it will be replaced by the display of the next
playback order. Programmed track numbers on the
selected disc will stop flashing and light up on the
music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1) Press the “+10” button.
(2) Within 3 seconds, press the “2” button.
5
Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6
Press the play/pause / button to start playback of
programmed tracks.
Notes
• It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
• During playback or pause, programming is not possible.
• If the total time of the programmed tracks becomes 100
minutes or more, the highest position of the figure will not
be displayed.
• The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
• Skip search can be performed during playback, but only
within the range of the programmed tracks.
• Manual search can be performed during playback to
search all tracks, including unprogrammed tracks.
• If programs are made selecting tracks from more than one
disc, pressing the DISC CHANGE button is useless during
program play.
CD CHANGER RECEIVER EMX–120CD PRESET/TUNING/BAND A/B/C/D/E
OPEN/CLOSE
DISC 1 DISC 2 DISC 3
DISC CHANGE
VOLUME INPUT SELECTOR
VCR•LD/TV•CD•TAPE/MD•TUNER
CD TUNER
STANDBY/ON
PHONES
KARAOKE
PROGRAM
MEMORY
MUSIC
DISPLAY MEMORY AUTO/MAN’L REPEAT TIME
TIME ADJ TIMER HOUR MIN
INPUT TRIM MIC TONE MIC MIC MIXING
SOFT NORMAL MAX MIN
ECHO ECHO
4
3
2
6
TIME
1
Display information during programming
Playback order
Music calendar Selected disc
Selected track number Total playing time
1 6
TRACK
PROGRAM MUSIC KARAOKE
PRO LOGIC
100 1K 10K PROG VOLUME
OVER
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
PROGRAM MUSIC KARAOKE
PRO LOGIC
100 1K 10K PROG VOLUME
OVER
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TIME