Speaker balance adjustment, E-16 adjustments, Before operation – Yamaha EMX120CD User Manual
Page 24: Time adj timer hour min, Soft normal max min echo echo, Press the standby/on switch to turn the power on, Tape/md ld/tv audio signal vcr subwoofer, Normal phantom
CD CHANGER RECEIVER EMX–120CD
PRESET/TUNING/BAND
A/B/C/D/E
OPEN/CLOSE
DISC
1
DISC
2
DISC
3
DISC
CHANGE
VOLUME
INPUT SELECTOR
VCR•LD/TV•CD•TAPE/MD•TUNER
CD
TUNER
STANDBY/ON
PHONES
KARAOKE
PROGRAM
MEMORY
MUSIC
DISPLAY
MEMORY
AUTO/MAN’L
REPEAT
TIME
TIME ADJ
TIMER
HOUR
MIN
INPUT TRIM
MIC TONE
MIC
MIC MIXING
SOFT
NORMAL
MAX
MIN
ECHO
ECHO
TIME
A
PROG
B
C
D
+
I0
E
CD
TUNER
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
0
PRESET
INPUT
MUSIC
PROGRAM
STANDBY/ON
DISPLAY
SLEEP
ECHO
FLAT
LEVEL
KARAOKE
VOLUME
DISC SKIP
STOP
PLAY/PAUSE
TUNER
CD
TEST
CENTER/REAR
/DELAY
OPEN/CLOSE
REPEAT
RANDOM
MODE
E-16
ADJUSTMENTS
Speaker balance adjustment
This procedure lets you adjust the sound output level balance
between the front, center, and rear speakers using the built-in
test tone generator. When this adjustment is performed, the
sound output level heard at the listening position will be the
same from each speaker. This is important for the best
performance of the built-in Dolby Pro Logic surround decoder.
The adjustment of each speaker output level should be
done at your listening position with the remote control
transmitter. Otherwise, the result may not be satisfactory.
Before operation
Set the CENTER MODE switch on the rear panel of this unit
to the position suitable for your speaker system configuration.
(Refer to page 7 for details.)
NORMAL (For 5-speaker configuration):
Select this position when you use the center speaker.
PHANTOM (For 4-speaker configuration):
Select this position when you do not use the center
speaker. The center sound will be output from the left
and right front speakers.
1
Press the STANDBY/ON switch to turn the power on.
2
Turn the VOLUME control counterclockwise to decrease
the volume to minimum.
3
Press the PROGRAM button once or more so that “
PRO LOGIC” lights up on the sound field program
indicator.
4
Press the TEST button.
* “TEST” flashes on and off on the display.
5
Press the VOLUME + (up) button to increase the volume.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
(L and R)
4
2
3
1
5
1
2, 5
3
SPEAKERS
CENTER/REAR
SPEAKERS
FRONT
MAINS
R
L
CENTER
REAR
REAR
REAR SINGLE
CENTER
:6
Ω
MIN./SPEAKER
6
Ω
MIN./SPEAKER
SEE OWNER’S MANUAL FOR CONNECTION.
SEE OWNER’S MANUAL FOR CONNECTION.
REAR
:4
Ω
MIN./SPEAKER
REAR SINGLE :8
Ω
MIN./SPEAKER
R
L
L
AUDIO SIGNAL
TAPE/MD
LD/TV
AUDIO SIGNAL
VCR
SUBWOOFER
R
IN
OUT
IN
OUT
OUT
VCR
MONITOR
OUT
LD/TV
VIDEO SIGNAL
ANTENNA
AM
FM
GND
75
Ω
UNBAL.
IN
OUT
VIDEO SIGNAL
50kHz
9kHz
10kHz
100kHz
FM
AM
FREQUENCY
STEP
CENTER
MODE
NORMAL
PHANTOM
AC OUTLET
UNSWITCHED
100W MAX.
VOLTAGE
SELECTOR
NORMAL
PHANTOM
CENTER
MODE