Honeywell ADEMCO LYNXR-EN - Manual (Page 55)

–55–
System Communication
Report 3+1/4+1 Standard 3+1/4+1 Expanded 4+2
Alarm SSS(S) A SSS(S) A
AAA(A) Z SSSS AZ
Trouble SSS(S) T SSS(S) T
TTT(T) t SSSS Tt
Bypass SSS(S) B SSS(S) B
BBB(B) b SSSS Bb
AC Loss SSS(S) E SSS(S) E
EEE(E) AC SSSS EAC
Low Battery SSS(S) L SSS(S) L
LLL(L) LB SSSS LLB
Open SSS(S) O SSS(S) O
OOO(O) U SSSS OU
Close SSS(S) C SSS(S) C
CCC(R) U SSSS CU
Test SSS(S) G SSS(S) G
GGG(G)g SSSS Gg
Restore Alarm SSS(S) R SSS(S) R
RRR(R) Z SSSS RZ
AC Restore SSS(S) RA SSS(S) RA
RARARA(RA)Ac
SSSSRA Ac
Low Battery Restore SSS(S) RL SSS(S) RL
RLRLRL(RL)LB
SSSS RLLB
Trouble Restore SSS(S) RT SSS(S) RT
RTRTRT (RT)t
SSSS RTt
Bypass Restore SSS(S) RB SSS(S) RB
RBRBRB (RB)b SSSS RBb
ADEMCO Contact ID® Reporting takes the following format: CCCC Q EEE GG ZZZ where:
CCCC = Customer (subscriber) ID
Q =
Event qualifier, where: E = new event, and R = restore
EEE = Event code (3 hex digits) (for a complete list of event codes, refer to the central office receiver manual)
GG =
Always “00”
ZZZ = Zone/Contact ID® number reporting the alarm, or user number for open/close reports. System
status messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location.
CONTACT ID® EVENT CODES
Code Definition
110 Fire Alarm
121 Duress
122
Alarm, 24-hour Silent
123 Alarm, 24-hour Audible
131 Alarm, Perimeter
132 Alarm, Interior
134 Alarm, Entry/Exit
135 Alarm, Day/Night
145 Wireless Dialer Tamper (plus Zone 93) (Alarm)
146 Silent Burglary
150 Alarm, 24-Hour Auxiliary
301 AC Power
338 Wireless Dialer Low Battery (plus Zone 93)
341 Wireless Dialer Tamper (plus Zone 93) (Trouble)
342* Wireless Dialer AC Loss (plus Zone 93)
344 RF Jam Detected
351* Wireless Dialer Phone Line Cut (plus Zone 93)
354 Fail to Report
355 Wireless Dialer Loss of RF Supervision
(plus Zone 93)
355 (Zone 000) Reported by the 5842 Wireless Dialer
373 Fire Loop Trouble
374 Exit Error Alarm
*If supported by the 5842 Wireless Dialer that is installed.
Code Definition
380 Global Trouble, Trouble Day/Night
381 RF Supervision Trouble
383 RF Sensor Tamper (Trouble)
384 RF Sensor Low Battery
401 Disarmed, Armed AWAY (NO DELAY),
Armed AWAY
403 Scheduled Auto Arm
406 Cancel by User
407 Remote Arm/Disarm (Downloading)
408 Quick Arm AWAY/NO DELAY
441 Disarmed/Armed STAY/NO DELAY, Quick Arm
STAY/NO DELAY
570 Bypass
602 Periodic
Test
606 AAV to follow
607 System Test
623 Event Log 80% Full
654 System Inactivity
NOTE: The following codes are logged in the event log upon
occurrence, but are not reported:
305 = System Reset
627 = Keypad Program Mode Entry