Heath Zenith UT-5666-AL - Manual (Page 2)

2 598-1288-04
Cover
Plate
Mounting
Plate
Lag Screw (3)
Flat Washer (9)
Photocontrol
Ground
Screw
1. Select a location on a flat wall with structurally sound wood
and from 10 to 25 feet (3 to 7.6 m) from the ground. The wood
should be at least one inch (25 mm) thick to safely secure the
fixture.
2. The fixture can be mounted with three lag screws and washers
which are provided.
3. Using the mounting template as a guide, mark three mounting
holes. We suggest drilling 3/16" (4.8 mm) pilot holes for the lag
screws.
4. Install the bottom two lag screws first. Screw in the lag screws
so that there is about 3/8" (9.5 mm) of space under the head.
5. Place the fixture on these two lag screws and install the top lag
screw. Tighten the top lag screw first, then tighten the remaining
lag screws
6. Secure your outdoor cable or flexible conduit to the cover plate
with a fitting in accordance with the National Electrical Code
(Canadian Electrical Code in Canada).
7. Thread the black and white fixture wires through the hole in the
cover plate as shown.
8. Connect the fixture wires to the service wires using the wire nuts
provided (black to black and white to white).
9. This fixture must be grounded. Connect the service ground under
the head of the green ground screw and secure to the fixture.
10. Install the cover plate. Secure with the two screws, two nuts and
four washers provided.
11. Install the lens/reflector assembly with two screws and washers
provided.
12. Screw in the 100 watt H.P. Sodium type S54 bulb provided.
Lens/Reflector
Assembly
Questions or problems? Before returning to your retailer, call our
technical service department at 1-800-858-8501 (English speaking
only), 7:30 am to 4:30 pm, CST, Monday – Friday.
InStaLLatIon InStructIonS
WItHout tWo PIece arm
Estimated Installation Time: 45 minutes
Items needed for installation (not included):
• Phillips and flathead screwdrivers
• 13 mm, 10 mm, and 8 mm sockets
• 3/16" Drill bit
• Drill
• Pliers • Wire strippers/cutters
• Safety glasses • Silicone caulk
• Ladder • Small box or rag
reaD aLL InStructIonS careFuLLY BeFore
BeGInnInG InStaLLatIon.
note: All wiring must be run in accordance with the National
Electrical Code (Canadian Electrical Code in Canada)
through conduit or another acceptable means. Contact a
qualified electrician if there is any question as to the suit-
ability of the system.
WarnInG: turn power off at the circuit breaker or
fuse.
13. Loosen the screw in the center of the photocontrol socket two
turns. Twist the socket so that the arrow points north. Note: There
is a stop to prevent the socket from turning all the way around.
If you have trouble turning the socket, try turning it the other
direction. Retighten the screw in the center of the socket.
14. Align the photocontrol (it will only plug-in one way). Plug it in
and twist clockwise until it stops.
To test operation during the daytime, cover the photocontrol with
a small box or rag. Turn the power on. Light should turn on and
reach full brightness within ten minutes. Remove the box or rag to
expose the photocontrol to daylight. Light should turn off within
two minutes. With the photocontrol exposed, the light will operate
automatically – on at dusk and off at dawn.
Package Contents and Fixture Assembly
Bulb
Lamp in Fixture contains mercury. Dispose according
to Local, State, or Federal Laws.