Harman-Kardon AVR80 - Manual (Page 28)

Basic Operation
22
ENGLISH
A. To use the front panel buttons simply
press and hold
TUNE ⁄ ^ button
until the desired letter or number
appears. Note that the upper case
alphabet will appear, followed by the
numbers
1 through 0 , and then a
indicating a blank space. Tapping the
button will advance the display one
character at a time; holding it down will
move the display quickly. If you pass by
the desired character, use the
TUNE ¤
^ to move the display in reverse.
After entering the first character, press
MEMO Ú to move to the next position
and note that the next digit will blink.
Use the same procedure outlined above to
enter a character.
When you have entered a digit or “blank”
in all five spaces, press
MEMO Ú for
more than 1 second to confirm the entry
B. To use the remote for character entry,
press the button corresponding to the
desired letter or number. Press it once to
enter the first printed letter, twice for the
second, three times for the third and four
times for the number. Press the “
9 ”
button to enter a blank space. (For
example, press the “
ABC ” button once
to enter an “ A ”, three times for a “ C ”
and four times to enter a “ 1 ”.)
Use the MEMO button o to move to
the next digit position. When all five
spaces have been filled, press
MEMO
again for more than 1 second to confirm
the entry.
Once a station name has been attached to
a preset position, the station’s frequency
will appear briefly when the unit is tuned
to that station. After a few seconds the
preset name will appear in the display.
Tuning Preset Stations
Stations preset into the tuner’s memory
may be recalled in a number of ways.
1. To recall a station directly enter a
number from 1 to 30 using the number
buttons on the remote s
m .
a. To enter a single digit memory
location, press
0 before the number,
or enter the number and wait a few
seconds.
b. If an invalid number (other than
1–30) is entered in error, that
number will flash to alert you that
the entry is invalid and the display
will return to the previous frequency
display.
2. To scan through the list of preset
stations, press the
P-SET ⁄ or P-SET
¤ on the front panel $ or the
CHANNEL buttons ‡ · remote k .
Press once to move up or down through
the memory presets one by one, or press
and hold the button to quickly scan
through the list of stations.
3. To automatically review each station
in the memory, press the
P-SCAN
button n % . Note that the P-SCAN
indicator › will blink.
The tuner will move up through the list
of stations, pausing to play each for five
seconds. Note that preset numbers where
no station has been programmed will be
skipped.
When the desired station is reached press
P-SCAN % or CLEAR Û .
Clearing Preset Stations
Once stations are programmed into the
preset memories, it is possible to remove
them individually or as a group.
To remove a single station from the
memory:
1. Recall the station by pressing the
buttons on the remote corresponding to
the station’s memory location.
2. Press the MEMO button Ú or o
and observe that the MEMO indicator £
will blink.
3. While the indicator is blinking, press
the
CLEAR button Û -not the CLEAR
button on the remote within five seconds.
The word
CLEAR will show briefly to
confirm that the memory position has
been cleared.
To clear all memory locations, the
volume level and surround mode
memories:
1. Press the MEMO button Ú o and
the CLEAR button Û m at the same
time for some seconds, until CLEAR
MEMO appears on the display.
NOTE: When a complete memory clear is
performed the AVR80 will turn off as part
of the process. After clearing the memory
it is necessary to reset all stations and set
up parameters.
AVR80 manual 11/01/98 13:01 Side 22