Isle o ale oo to e – Hearth and Home Technologies QUADRA-FIRE 823-0170 - MBK User Manual
Page 16

R
Page
16
250-5763F
March
21,
2013
Isle o ale oo to e
i ne eig t ise an un
This product was designed for and tested on a 6 inch
(152mm) chimney, 12 to 14 feet (420-480cm) high, (includes
stove height) measured from the base of the appliance to
the the top of the chimney (not including chimney cap).
The further your stack height or diameter varies from this
FRQ¿JXUDWLRQWKHSRVVLELOLW\RISHUIRUPDQFHSUREOHPVH[LVWV
Chimney height may need to be increased by 2 - 3% per
each 1000 feet above sea level. It is not recommended to
use offsets or elbows at altitudes above 4000 feet above sea
OHYHORUZKHQWKHUHDUHRWKHUIDFWRUVWKDWDIIHFWÀXHGUDIW
Fire is .
Inspection of Chimney:
&KLPQH\PXVWEHLQJRRGFRQGLWLRQ
0HHWVPLQLPXPVWDQGDUGRI1)3$
)DFWRU\EXLOWFKLPQH\PXVWEHLQFK
PP8/+7
I
Chimney Flue
Liner
Fireclay
Liner or
Equivalent
Masonry Chimney
Constructed to NFPA 211
Wall Spacer
Wall Band
Trim Collar
Chimney
Connector
1 inch (25mm) Air
Space to Chimney
Section
Min. Clearance
2 inch (51mm)
Min. Chimney Clearance to
Wall Spacer and
Combustibles - 2 inch (51mm)
Chimney Section
Figure 1 .1 oli a
i ne wit etal upports
as a
i
le ont
I
'2127&211(&77+,681,772$&+,0-
1(<)/8(6(59,&,1*$127+(5$33/,-
$1&(
'2127&211(&772$1<$,5',675,%8-
7,21'8&7256<67(0
0D\DOORZÀXHJDVHVWRHQWHUWKHKRXVH
sp
iation is .
asonr
i ne iner
For optimal performance, masonry chimneys used to vent
this appliance should be:
/LQHGZLWKDLQFKPPVWDLQOHVVVWHHOOLQHU
,QVWDOODWLRQVLQWRDFOD\ÀXHZLWKRXWDVWDLQOHVVVWHHO
liner may reduce draw which affects performance,
cause the glass to darken and produce excessive
creosote.
2. It is recommended that a chimney with a larger diameter
than 6 inches (152mm) be relined.
7KHRYHUVL]HGÀXHFDQFDXVHSRRUSHUIRUPDQFHDQG
contribute to the accumulation of creosote.
3. Have the chimney cleaned before the stove is installed
and operated.
The following bullets list the more critical requirements for a
properly constructed chimney:
The masonry wall of the chimney, if brick or modular
block, must be a minimum of 4 inches (102mm) nominal
thickness.
$ FKLPQH\ RI UXEEOH VWRQH PXVW EH DW OHDVW LQFKHV
(305mm) thick.
7KHFKLPQH\PXVWKDYHD¿UHFOD\ÀXHOLQHURUHTXLYDOHQW
with a minimum thickness of 5/8 inch (16mm) and must
be installed with refractory mortar.
$QHTXLYDOHQWOLQHUPXVWEHDOLVWHGFKLPQH\OLQHUV\VWHP
or other approved material.
6LQFHDQRYHUVL]HGÀXHFRQWULEXWHVWRWKHDFFXPXODWLRQ
RI FUHRVRWH WKH VL]H RI WKH ÀXH VKRXOG EH FKHFNHG WR
determine that it is not too large for the insert.
The chimney should also be checked to ensure it meets
the minimum standard of the National Fire Protection
$VVRFLDWLRQ1)3$6WDQGDUG
$ FKLPQH\ VXSSRUW SDFNDJH PXVW EH XVHG ZKHQ D
connection is made through the ceiling to a factory built
chimney.
$Q DSSURYHG WKLPEOH DQG FKLPQH\ VXS
SRUW SDFNDJH
are
a solutel ne essar to provide safe clearances to
combustible wall and
ceiling material.
NOTICE: In Canada, the installation shall conform to
&$1&6$%
NOTICE: Check with your local building authorities
DQGRUFRQVXOWWKH1DWLRQDO)LUH3URWHFWLRQ$VVRFLDWLRQ
1)3$