Harman-Kardon AVR 745 - Manual (Page 13)

ZONE II REMOTE CONTROL FUNCTIONS 13
ENGLISH
Zone II Remote Control Functions
G Numeric Keys: These buttons serve as a
ten-button numeric keypad to enter tuner preset
positions. They are also used to select channel
numbers when TV, VCR or Sat receiver has been
selected on the remote, or to select track num-
bers on a CD, DVD or LD player, depending on
how the remote has been programmed.
H Disc Skip: Press this button to change discs
on compatible Harman Kardon CD or DVD
changers.
I Volume Up/Down: When used in the room
where the AVR is located, press this button to
raise or lower the volume in that room. When it
is used in a remote room with a sensor that is
connected to the Multi IR Jack
O, this button
will raise or lower the volume in the remote
room.
J Blank Buttons: These buttons are not
active. Pressing them will not change or control
any function on the AVR 745 or other IR devices.
K Mute: When used in the room where the
AVR is located, press this button to temporarily
silence the unit. When it is used in a remote
room with a sensor that is connected to the
Multi IR Jack
O, this button will temporarily
silence the feed to the remote room only. Press
the button again to return to the previous
volume level.
Important Note: No matter in which room the
Zone II remote is used, as with the main remote
it is important to remember to press the Input
Selector button
D that corresponds to the
unit you wish to operate befor you change the
device to be controlled.
L Clear Button: Press this button to clear
incorrect entries when using the remote to directly
enter a radio station’s frequency.
M Direct Button: Press this button when the
tuner is in use to start the sequence for direct
entry of a station’s frequency. After pressing the
button simply press the proper Numeric Keys
G to select a station (See page 57 for more
information on the tuner).
N Memory Button: Press this button to enter
a radio station into the AVR’s preset memory. Two
underline indicators will flash at the right side of
the Main Information Display ˜, you then
have five seconds to enter a preset memory
location using the Numeric Keys
G. (See
page 57 for more information.)
O Tuner Mode: Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so
MANUAL appears in the Main
Information Display ˜, pressing the Tuning
buttons
K will move the frequency up or down
in single-step increments. When the FM band is
in use and
AUTO appears in the Main
Information Display ˜, pressing this button
will change to monaural reception making even
week stations audible. (See page 57 for more
information.)
P Transport Control Buttons: These buttons
do not have any functions for the AVR, but they
are programmed for the forward/reverse play
operation of a wide variety of Harman Kardon
CD or DVD players, and audio or video- cassette
recorders.
Q Set Button: This button is used to enter
settings into the AVR’s memory. It is also used in
the setup procedures for delay time, speaker con-
figuration and channel output level adjustment.
Digital Media Player (DMP)
Selector: When Harman Kardon’s
(optional) is connected to
Digital
Media Player (DMP) Connector 8 and a
compatible Apple ® iPod ® is docked in ,
pressing this selector will select the iPod as the
audio source input device for the AVR 745. In
addition, if a video display is connected to one of
the Video Monitor Outputs
B, the iPod’s
messages will appear on screen, and in the
Upper and Lower Display Lines ˜. The
⁄ / ¤ / ‹ / › Buttons DF, the Set Button
EQ and the Transport Controls AP
may be used to navigate the iPod and to operate
many functions. See page 50, and the manuals
for The Bridge and your iPod for more informa-
tion.
29510_AVR745_Engelsk 30/10/06 9:31 Side 13