Roland JUPITER-X Synthesizer - Manual (Page 27)

JUPITER-X Owner's Manual Ver. 1.5 and later
27
Parameter
[1] knob
Value
[2] knob
Explanation
Arp Sync (*1)
OFF, BEAT,
MEASURE
Specifies the synchronization setting for
arpeggio performance when connected to an
external device and playing in synchronization.
OFF: Does not synchronize to measures or
beats. Arpeggio performance starts at the
moment that MIDI messages are received.
BEAT: Synchronizes to beats. Arpeggio
performance starts at the next beat after MIDI
messages are received.
MEASURE: Synchronizes to measures.
Arpeggio performance starts at the first beat
of the next measure after MIDI messages are
received.
(*1) This is only enabled when Sync Mode is set to “MIDI,” “USB COM” or “USB MEM.”
TEMPO/SYNC
Tempo 20.00–300.00 Specifies the system tempo.
Tempo Src SCENE, SYS
When you switch scenes, this setting specifies
whether to use the system tempo (SYS) or the
tempo stored in the scene (SCENE).
Sync Mode
AUTO, INT, MIDI,
USB COM,
USB MEM
Specifies the synchronization signal according
to which the JUPITER-X operates.
Sync Out
OFF, MIDI,
USB COM,
MIDI/USBCM,
USB MEM, ALL
Specifies the connector from which MIDI clock
messages etc. are output.
BLUETOOTH
Bluetooth Sw OFF, ON
Enables (ON) or disables (OFF) Bluetooth
communication.
Pairing - Executing pairing for Bluetooth audio.
Bluetooth ID OFF, 1–9
Specifies the number added to the end of
this unit’s device name shown in a Bluetooth-
connected app.
MIDI
Ctrl Ch 1–16, OFF
Specifies the MIDI receive channel on which
MIDI messages (program change and bank
select) from an external MIDI device can be
received to switch programs.
If you don’t want programs to be switched
from a connected MIDI device, turn this “OFF.”
Ctrl Src Sel SYS, SCENE
SYS: SysCtrlSrc1–4 are used for tone control.
SCENE: The scene’s CtrlSrc1–4 settings are
used for tone control.
SysCtrlSrc1
SysCtrlSrc2
SysCtrlSrc3
SysCtrlSrc4
OFF, CC01-CC31,
CC33-CC95,
BEND, AFT
Specify the MIDI messages that will be used as
system controls.
Soft Thru OFF, ON
If this is ON, MIDI messages that are input
from the MIDI IN connector are re-transmitted
without change from the MIDI OUT connector.
USB-MIDIThru OFF, ON
Specifies whether MIDI messages received at
the USB COMPUTER port/MIDI IN connector are
retransmitted without change from the MIDI
OUT connector/USB COMPUTER port (ON) or
are not retransmitted (OFF).
USB Driver
VENDOR,
GENERIC
Specifies the USB driver setting.
Remote Kbd
OFF, MIDI IN,
USB COM,
USB MEM
Sets which connector is used for input when
you use an external MIDI keyboard instead of
the keyboard of the JUPITER-X. In this case,
the MIDI transmit channel of the external MIDI
keyboard does not matter.
Normally you will leave this “OFF.”
Local Sw OFF, ON
Turns on/off the connection between the
controller section (keyboard, PITCH, MODE,
panel buttons and sliders, pedals, etc.) and the
internal sound engine.
Parameter
[1] knob
Value
[2] knob
Explanation
Age
OFF,
1–100 [years]
Simulates the aging of an analog synthesizer’s
internal components. Increasing this value
changes the sound as it would be on a unit
that is a corresponding number of years old.
This is valid only for sounds of an analog
synthesizer model.
GENERAL
MasterTune 415.3–466.2 [Hz]
Adjusts the overall tuning.
The displayed value is the frequency of the A4
key (middle A).
MasKeyShift -24–24
Shifts the JUPITER-X’s overall pitch range in
semitone steps.
ScaleTuneSw OFF, ON
Specifies whether the scene’s SCALE TUNE
setting is enabled (ON) or disabled (OFF).
USB In Lev 0–127
Adjusts the audio input level of the USB
COMPUTER port.
USB Out Lev 0–127
Adjusts the audio output level to the USB
COMPUTER port.
AuxIn/BT InLev 0–127 Adjusts the input level of the AUX IN jack.
USB Audio Thru OFF, ON
Specifies whether the audio input of the USB
COMPUTER port is mixed into the audio output
of the USB COMPUTER port.
If you don’t want to output this audio, turn
this “OFF.”
AUXIN USB Thru OFF, ON
Specifies whether the input of the AUX IN
jack is mixed into the audio output of the USB
COMPUTER port.
If you don’t want to output this audio, turn
this “OFF.”
Line Out Gain -12–0–+12 [dB] Adjusts the output gain of OUTPUT/PHONES.
Speaker Sw OFF, ON, AUTO
Specifies whether sound is output from the
speakers. The AUTO setting operates as “OFF”
when headphones are connected and as “ON”
when headphones are not connected.
SPOut Gain -12–0 [dB] Adjusts the output gain of the speakers.
Auto Off
OFF, 30 [min],
240 [min]
Specifies whether the unit will turn off
automatically after a certain time has elapsed.
If you don’t want the unit to turn off
automatically, choose “OFF” setting.
LED On Bright 0–31 Adjusts the brightness when the LEDs are lit.
LED OffBright 0–30
When the JUPITER-X is operating, you can make
the LEDs remain dimly lit when off instead of
going completely dark.
This setting adjusts the LED brightness when off.
LCD Contrast 1–10 Adjusts the contrast of the display.
Scene Lock OFF, ON
Specifies whether a confirmation screen
appears when you recall a scene.
OFF: The scene is recalled immediately.
ON: Before the scene is recalled, a confirmation
screen appears. To recall the scene, use the
PAGE [<][>] buttons to select “Yes,” and then
press the [ENTER] button.
Startup Scene 01-01–16-16
Specifies the scene that is recalled when the
unit starts up.
ARPEGGIO
Set Tone OFF, ON
Specifies whether the current sound settings
are kept while only the phrase is switched
(OFF) or both the phrase and the sound
settings are switched (ON).
Set Drumkit OFF, ON
Specifies whether the current sound settings
are kept while only the rhythm is switched
(OFF) or both the rhythm and the sound
settings are switched (ON).
Set Tempo OFF, ON
Specifies whether the current tempo setting is
kept while only the rhythm is switched (OFF)
or both the rhythm and the tempo settings are
switched (ON).